(2) Put the access platform in position. Subtask 78-32-11-040-050
E. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041). Subtask 78-32-11-010-060
F. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
FOR 1000EM1
451AL, 452AR
FOR 1000EM2
461AL, 462AR
4. Procedure
_________
(Ref. Fig. 301/TASK 78-32-11-991-301) Subtask 78-32-11-020-050
A. Removal of the One or Eleven O'clock Strut Bushing
(1) Remove the screws (5) and the nuts (10) that attach the pin (15) to the inner barrel.
(2) Remove the pin (15) and the bushing (20).
(3) Discard the bushing (20).
(4) Remove the sealant from the bottom of the inner barrel with a plastic scraper.
(5) In necessary, remove the sealant from around the strut.
F 『 EEFF : ALL E Page 30378-32-11
E E May 01/05 ERE
ECES E F 『 E C F M E E E E 56-5B E
Replacement of the One or Eleven O'clock Strut Bushing
Figure 301/TASK 78-32-11-991-301
F 『 EEFF : ALL E Page 30478-32-11
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(6) Cleaning:
WARNING : BEFORE THE USE OF SOLVENT, PROTECTIVE FILM OR SEALANT
_______ CAREFULLY READ THE APPLICABLE "MATERIAL SAFETY DATA SHEET" AND FOLLOW ALL LISTED SAFETY AND HEALTH PRECAUTIONS. USE THESE PRODUCTS IN AN AREA OPENED TO THE AIR AND WEAR PROTECTION GLOVES. THESE PRODUCTS ARE FLAMMABLE AND VAPOR IS DANGEROUS. THEY MAY CAUSE IRRITATION OF EYES, NOSE, THROAT AND SKIN. HIGH CONCENTRATIONS MAY CAUSE WEAKNESS, HEADACHE, NAUSEA, DIZZINESS AND IMPAIRED JUDGEMENT.
R (a) Clean the areas where you removed the sealant with acetone
R (Material No. CP1039) or stoddard solvent (Material No. CP2011)
R or ardrox 552 (Material No. CP2559) or turco ind 79 (Material No.
R CP2560) or mag-chem teksol (Material No. CP2566) or degreasol 99R
R (Material No. CP2584) or mag-chem skysol (Material No. CP2656) or
R isopropyl alcohol (Material No. CP1041).
(7) Dry the areas with a clean cloth.
F 『 EEFF : ALL E Page 30578-32-11
E E May 01/05 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-32-11-400-001 Installation of the One or Eleven O'clock Strut Bushing
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice No specific access platform 1 m (3 ft. 3 in.) No specific Torque Wrench : range 31 to 40 lbf.in
(0.35 to 0.45 m.daN)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. CP2303 * RTV732 (Ref. 70-30-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
20 bushing 78-32-01 02 -110 20 bushing 78-32-01 02 -110A
F 『 EEFF : ALL E Page 30678-32-11
E E May 01/05 ERE
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 78-32-11-991-301 Fig. 301
3. Job Set-up
__________
Subtask 78-32-11-860-050
A. Aircraft Maintenance Configuration
(1) On the center pedestal, on the ENG panel 115VU, make sure that a warning notice is in position to tell persons not to start the engine.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EXHAUST 2(48)
