F 『
E C F M E
E E
E 56-5B E
E E
(2) Installation of the Middle Half Door Stirrup
(a) Put the stirrup (30) in position and install the tension nut (20). Tighten the nut with your hand.
NOTE : Do not torque the nut at this time. The nut will be
____ torqued during the adjustment procedures for the thrust reverser half door latches.
(b) Put the locking bracket (10) over the tension nut (20) and loosely install the screw (15).
(3) Installation of the Forward Half Door Stirrups
(a) Put the stirrups (30) in position and install the tension nuts (20). Tighten the nuts with your hand.
NOTE : Do not torque the nuts at this time. The nuts will be
____ torqued during the adjustment procedures for the thrust reverser half door latches.
(b) Put the locking brackets (10) over the tension nuts (20) and loosely install the screws (15).
Subtask 78-36-41-410-052
B. Close Access
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Close the left thrust reverser half door (Ref. TASK 78-36-00-410-040). FOR 1000EM1 451AL FOR 1000EM2 461AL
Subtask 78-36-41-820-050
C. Adjust the thrust reverser half door latches (Ref. TASK 78-36-41-820-042).
F 『 EEFF : ALL E Page 41778-36-41
E E Feb 01/98 E E ECES E 5. Close-up
F 『
E C F M E
E E
E 56-5B E
E E
________ Subtask 78-36-41-440-051
A. Make the thrust reverser serviceable (Ref. TASK 78-30-00-081-041). Subtask 78-36-41-410-053
B. Close Access
(1) Close the fan cowls: (Ref. TASK 71-13-00-410-040)
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
(2) Remove the warning notice(s).
F 『 EEFF : ALL E Page 41878-36-41
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
TASK 78-36-41-000-045 Removal of the Thrust Reverser Half Door Centering Pins
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
Maintenance 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-41-991-301 Fig. 402
3. Job Set-up
__________ Subtask 78-36-41-941-052
A. Safety Precautions
(1) On the center pedestal, on the ENG panel 115VU:
(a) Put a warning notice to tell persons not to start the engine.
(2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.
(3) On the overhead maintenance panel 50VU:
(a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.
F 『 EEFF : ALL E Page 41978-36-41
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(b) Put a warning notice to tell persons not to energize the FADEC 1(2).
Subtask 78-36-41-010-054
B. Open fan cowl doors (Ref. TASK 71-13-00-010-040):
FOR 1000EM1
437AL, 438AR
FOR 1000EM2
447AL, 448AR
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EXHAUST 2(103)
