• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-27 17:17来源:蓝天飞行翻译 作者:航空
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 E  56-5B  E
 E  E


 D. Close Access
 (1) Close the fan cowl doors (Ref. TASK 71-13-00-410-040):
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR


 (2) Remove the access platform(s).


 (3) Remove the warning notice(s). Subtask 78-31-51-614-057
 E. Pressurize the aircraft hydraulic systems.
 (1) For engine 1 pressurize the Green hydraulic reservoir (Ref. TASK 29-14-00-614-002).

 (2) For engine 2 pressurize the Yellow hydraulic reservoir (Ref. TASK 29-14-00-614-002).


 Subtask 78-31-51-710-057
 F. Bleed the air from the thrust reverser hydraulic system (Ref. TASK 78-30-00-710-040).
 F 『 EEFF : ALL E Page 42878-31-51
 E E May 01/05 ERE
ECES E CONTROL UNIT - HYDRAULIC (4101KS) - INSPECTION/CHECK

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E


____________________________________________________
 TASK 78-31-51-210-040
 Detailed Visual Inspection of the Hydraulic Control Unit
 1. Reason for the Job
__________________
 Self Explanatory
 2. Job Set-up Information
______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
 -------------------------------------------------------------------------------
No specific warning notice
 No specific access platform 1 m (3 ft. 3 in.)

 B. Referenced Information
 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
71-13-00-010-040 Opening of the Fan Cowl Doors 71-13-00-410-040 Closing of the Fan Cowl Doors 78-30-00-081-041 Make the Thrust Reverser Serviceable after
 Maintenance 78-30-00-481-041 Make the Thrust Reverser Unserviceable for
 Maintenance 78-31-51-000-042 Removal of the Hydraulic Control Unit 78-31-51-400-042 Installation of the Hydraulic Control Unit 78-36-00-010-040 Opening of the Thrust Reverser Doors 78-36-00-410-040 Closing of the Thrust Reverser Doors 78-31-51-991-302 Fig. 601
 F 『 EEFF : ALL E Page 60178-31-51
 E E Feb 01/98 E E ECES E

 F 『
 E C F M E
 E E
 E 56-5B E
 E E


 3. Job Set-up
__________
 Subtask 78-31-51-941-053
 A. Safety Precautions
 (1) On the center pedestal, on the ENG panel 115VU:

 (a) Put a warning notice to tell persons not to start the engine.

 (2) Make sure that the engine 1(2) shutdown occurred not less than 5 minutes before you do this procedure.

 (3) On the overhead maintenance panel 50VU:

 (a) Make sure that the ON legend of the ENG/FADEC GND PWR/1(2) pushbutton switch is off.

 (b) Put a warning notice to tell persons not to energize the FADEC 1(2).

 


 Subtask 78-31-51-010-056
 B. Get Access
 (1) Open the fan cowl doors: (Ref. TASK 71-13-00-010-040)
 FOR 1000EM1
 437AL, 438AR
 FOR 1000EM2
 447AL, 448AR


 (2) Put the access platform in position.


 Subtask 78-31-51-040-052
 C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
 Subtask 78-31-51-010-057
 D. Open the thrust reverser doors: (Ref. TASK 78-36-00-010-040)
 FOR 1000EM1
 451AL, 452AR
 FOR 1000EM2
 461AL, 462AR

 F 『 EEFF : ALL E Page 60278-31-51
 E E Feb 01/98 E E ECES E 4. Procedure

 F  『
 E  C F M  E
 E  E
 E  56-5B  E
 E  E


_________
 (Ref. Fig. 601/TASK 78-31-51-991-302)
 Subtask 78-31-51-210-051
 A. Do a visual inspection of the hydraulic control unit as follows:
 -------------------------------------------------------------------------------INSPECT/CHECK MAXIMUM REMARKS SERVICEABLE LIMITS -------------------------------------------------------------------------------
1. Examine the hydraulic control unit for:
 A. Damage  No damage permitted If you find some damage, replace the hydraulic control unit (Ref. TASK 78-31-51-000-042) and (Ref. TASK 78-31-51-400-042).
 B. Crack  No crack permitted If you find a crack, replace the hydraulic control unit (Ref. TASK 78-31-51-000-042) and (Ref. TASK 78-31-51-400-042).
 C. Leakage  No leakage permitted If there is leakage, check the coupling nuts and nipples for the correct torque (Ref. TASK 78-31-51-400-042). If the leakage persists, replace the preformed packing (Ref. TASK 78-31-51-000-042) and (Ref. TASK 78-31-51-400-042). If the leakage persists, replace the nipples (Ref. TASK 78-31-51-000-042) and (Ref. TASK 78-31-51-400-042).
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM EXHAUST 2(41)