(2) Put the access platform in position in the right side of engine.
F 『 EEFF : ALL E Page 40278-31-51
E E Feb 01/98 E E ECES E
F 『
E C F M E
E E
E 56-5B E
E E
Subtask 78-31-51-040-051
C. Make the thrust reverser unserviceable (Ref. TASK 78-30-00-481-041).
Subtask 78-31-51-010-053
D. Open the right thrust reverser cowl door (Ref. TASK 78-36-00-010-040): FOR 1000EM1 452AR FOR 1000EM2 462AR
Subtask 78-31-51-614-050
E. Depressurization of the Hydraulic Reservoirs
(1) For engine 1 depressurize the Green hydraulic reservoir (Ref. TASK 29-14-00-614-001).
(2) For engine 2 depressurize the Yellow hydraulic reservoir (Ref. TASK 29-14-00-614-001).
4. Procedure
_________
(Ref. Fig. 401/TASK 78-31-51-991-301)
Subtask 78-31-51-020-051
A. Removal of the Hydraulic Control Unit (HCU)
(1) Disconnect the electrical connector 4101KS-A from solenoid A of the HCU.
NOTE : If necessary, use the softnose pliers to loosen the electrical
____
connectors.
(2) Disconnect the electrical connector 4101KS-B from solenoid B of the HCU.
(3) Disconnect the electrical connector 4102KS-A from the HCU pressure switch.
(4) Remove the nut (25) and the bolt (5) that attach the clamp (10) to the interface bracket (15).
(5) Move the right thrust reverser harness (30) aside.
F 『 EEFF : ALL E Page 40378-31-51
E E Feb 01/98 E E ECES E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E F 『 E C F M E E E E 56-5B E
Hydraulic Control Unit
Figure 401/TASK 78-31-51-991-301- 13 (SHEET 1)
F EEFF : ALL 『E 78-31-51 Page 404
E E Feb 01/98
E E
ECES E
Hydraulic Control Unit
Figure 401/TASK 78-31-51-991-301- 23 (SHEET 2)
F EEFF : ALL 『E 78-31-51 Page 405
E E Feb 01/98
E E
ECES E
Hydraulic Control Unit
Figure 401/TASK 78-31-51-991-301- 33 (SHEET 3)
F EEFF : ALL 『E 78-31-51 Page 406
E E Feb 01/98
E E
ECES E
F 『
E C F M E
E E
E 56-5B E
E E
(6) Put a cover on the engine case to keep hydraulic fluid off.
(7) Disconnect hoses:
R WARNING : DO NOT GET THE FLUID ON YOUR SKIN OR IN YOUR EYES. IF YOU_______
R DO:
R - FLUSH IT AWAY WITH CLEAN WATER
R - GET MEDICAL AID.
(a) Disconnect the supply hose (50), the return hose (45), and the latch return hose (40) from the left side of the HCU (20). Drain hydraulic fluid into the drain can.
(b) Disconnect the latch supply hose (55), the head supply hose (60), and the rod supply hose (65) from the pipes at the interface bracket (15).
(8) Disconnect the CVR pipe (100) from the check valve restrictor.
(9) Remove the nut (95) that attaches the CVR pipe (100) to the support (90). Remove the CVR pipe (100).
(10) Remove the nut (105) that attaches the rod supply pipe (75) to the interface bracket (15).
(11) Remove the nuts (80) and (85) that attach the latch return pipe (35), the head supply pipe (70) and the support (90) to the interface bracket (15).
(12) Disconnect the latch supply pipe (110), the head supply pipe (70) and the rod supply pipe (75) from the right side of the HCU (20).
(13) Remove the bolts (115) that attach the HCU (20) to the forward frame. Remove the HCU (20).
(14) Remove the thermal blankets as follows:
(Ref. Fig. 402/TASK 78-31-51-991-303)
NOTE : Removal of the thermal blanket is not required, and is
____ included for reference only. The thermal blanket must be installed if the HCU is to be returned to the supplier.
(a) Remove the bolts (120) that attach the interface bracket (15) to the HCU (20).
(b) Remove the thermal blankets (175) and (180) from the HCU (20).
F 『 EEFF : ALL E Page 40778-31-51
E E Feb 01/05 E E ECES E F 『 E C F M E E E E 56-5B E
Hydraulic Control Unit Thermal Blankets
Figure 402/TASK 78-31-51-991-303
F EEFF : ALL 『E 78-31-51 Page 408
E E Feb 01/98
E E
ECES E
F 『
E C F M E
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM EXHAUST 2(34)
