-make sure that the protective cover is removed.
(5)
Make sure that the side stick assembly is installed on the HOLDER -SIDE STICK (98D27303001001) (Ref. TASK 27-92-41-000-001).
(6)
Make sure that the PIN-SIDE STICK LOCKING (98D27903500000) is in position on the center universal joint of the side stick assembly.
(7)
Make sure that the warning notice which tells persons not to operate the side stick is in position on the side stick.
1EFF : ALL 1 27-92-41Page 419 1 1 May 01/03R 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 404/TASK 27-92-41-991-003-A) Subtask 27-92-41-420-051-A
A. Installation of the Side Stick Transducer-Unit
(1)
Clean the component interface and/or the adjacent area.
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Remove the blanking caps from the electrical connectors.
(4)
Make sure that the electrical connectors are clean and in the correct condition.
(5)
Install the transducer unit (37) on the base of the side stick assembly and connect it to the electrical connectors (39).
(6)
Install the nuts (38) and tighten. or install the washers (45), the screws (38) and tighten.
Subtask 27-92-41-820-051-A
B. Adjustment of the Actuating Linkage
(1)
Install the RIGGING PIN (98DNSA20206080) (43) on the transducer unit (37).
(2)
Cut and discard the lockwire from the bolts (44).
(3)
Remove the washers (42) and the bolts (44).
(4)
Remove the rod retainers (40).
(5)
Connect one rod (32) to the transducer unit (37).
(6)
Install the bolt (33). If you cannot install freely the bolt (33), adjust the length of the rod (32) as follows:
(a)
Cut and discard the lockwires.
(b)
Loosen the nuts (30) and disengage the lockwashers(31).
(c)
Turn the rod body (32) until you can install the bolt (33).
1EFF : ALL 1 27-92-41Page 420 1 1 May 01/03R 1 1 1CES 1
(d)
Engage the lockwashers (31) and tighten the nuts(30).
(e)
Safety the nuts with MISCELLANEOUS (Material No. 19-009).
(7)
Install the washer (36), the nut (34) and tighten.
(8)
Install the new cotter pin (35) on the nut (34).
(9)
Make sure that you can remove and install freely the RIGGING PIN
(98DNSA20206080) (43) on the transducer unit (37).
(10)
Connect the other rod (32) to the transducer unit (37).
(11)
Install the bolt (33). If you cannot install freely the bolt (33), adjust the length of the rod (32) as follows:
(a)
Cut and discard the lockwires.
(b)
Loosen the nuts (30) and disengage the lockwashers (31).
(c)
Turn the rod body (32) until you can install the bolt (33).
(d)
Engage the lockwashers (31) and tighten the nuts (31).
(e)
Safety the nuts with lockwire-corrosion resistant steel dia. 0.8 mm (0.03 in.).
(12)
Make sure that you can remove and install freely the bolt (33).
(13)
Install the washer (36), the nut (34) and tighten.
(14)
Install the new cotter pin (35).
(15)
Make sure that the clearance J2 between the ends of the bolts (33) is
0.5 mm (0.0196 in.) (Ref. Detail B).
(16)
Put the rod retainers (40) in position.
(17)
Install the washers (42) and the bolts (44).
(18)
TORQUE the bolts (44) to between 0.3 and 0.4 m.daN (26.54 and 35.39 lbf.in).
(19)
Safety the bolts (44) with the nuts of the rod (32) with lockwire-corrosion resistant steel dia. 0.8 mm (0.03 in.).
1EFF : ALL 1 27-92-41Page 421 1 1 May 01/03R 1 1 1CES 1
(20) Make sure that you can remove and install freely the RIGGING PIN (98DNSA20206080) (43) on the transducer unit (37). ________
5. Close-up
Subtask 27-92-41-080-051
A. Removal of the Tools
(1)
Remove the RIGGING PIN (98DNSA20206080) from the transducer unit.
(2)
Remove the HOLDER - SIDE STICK (98D27303001001) from the side stick assembly.
Subtask 27-92-41-410-051
B. Install the side stick assembly (Ref. TASK 27-92-41-400-001).
1EFF : ALL 1 27-92-41Page 422 1 1 May 01/03R 1 1 1CES 1
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵9(45)
