• 热门标签

当前位置: 主页 > 航空资料 > 机务资料 >

时间:2011-03-22 06:40来源:蓝天飞行翻译 作者:admin
曝光台 注意防骗 网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者

 -------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/ELAC1/NORM/SPLY 15CE1 B11 49VU FLIGHT CONTROLS/THS/ACTR/MOT2 19CE2 B09 105VU FLT CTL/ELAC1/STBY SPLY 16CE1 A01 121VU FLIGHT CONTROLS/THS ACTR/MOT3 19CE3 Q17 121VU FLIGHT CONTROLS/THS ACTR/MOT1 19CE1 Q16


 Subtask 27-92-13-481-050
 D. Install Locking Devices
 (1) Put the PIN-SIDE STICK LOCKING in the CAPT and F/O side stick
 controllers. R
 Subtask 27-92-13-941-050
 E. Safety Precautions
 (1)
 Put the warning notices in the flight compartment to tell persons not to operate the flight controls.

 (2)
 Put the warning notices in position to tell persons not to operate the hydraulic systems.


 (3) Put the access platform in position at zones 334 and/or 344.
 Subtask 27-92-13-020-050

 F. Access
 (1) Open the horizontal stabilizer trailing edge access panels (Ref. TASK 55-13-11-000-001). For 49 CE1 remove panels 334BT and 334DB For 49 CE2 remove panels 344BT and 344DB
 4. Procedure
_________
 (Ref. Fig. 401/TASK 27-92-13-991-001)
 Subtask 27-92-13-020-052
 A. Disconnect the Bonding Strap and the Electrical Connectors
 (1)
 Disconnect the bonding strap from the control rod.

 (2)
 Remove the nut (11), the washer (10), and the bolt (8). Disconnect the bonding strap (9).

 (3)
 Disconnect the electrical connectors (3) from the receptacles (2).

 (4)
 Put blanking caps on the disconnected electrical connectors.

 


 Elevator-Servocontrol Position Transducer Unit Figure 401/TASK 27-92-13-991-001
 1EFF : 1 1R 1CES  ALL  1 11 1 27-92-13 Page 404 Feb 01/00

 

 Subtask 27-92-13-020-051
 B. Removal of the Elevator Position Transducer 
R R  (1) Make sure that the rigging pin can be inserted in the elevator position transducer 
R  NOTE : The rigging pin is part of the position transducer____ 
R  (2) Remove and discard the cotter pin (14). 
R  (3) Remove the nut (13), the washer (12), the bolt (5) and the bush (6) which attach the control rod (7) to the elevator position transducer (1). 
R  (4) Remove the control rod (7) from the elevator position transducer (1). 
R  (5) Remove the bolts (24) and the washers (25) which attach the mounting bracket (15) to its supports. 
R  (6) Remove and discard the cotter pins (18) and (22). 
R  (7) Remove the nuts (17), the washers (16) and the lower attaching bolts (4). 
R  (8) Remove the nut (21), the washer (20) and the upper attaching bolt (19). 
R  (9) Remove the elevator position transducer (1) from the mounting bracket (15).

 

 TASK 27-92-13-400-001 Installation of the Elevator Servocontrol Position Transducer Unit 49CE1, 49CE2 WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
 GEAR.

 WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE CLEAR.
_______
 MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR
 DAMAGE.

 WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
 START A TASK ON OR NEAR:

 -
THE FLIGHT CONTROLS

 -
THE FLIGHT CONTROL SURFACES

 -
THE LANDING GEAR AND THE RELATED DOORS


 -COMPONENTS THAT MOVE. WARNING : WEAR AND ATTACH A SAFETY HARNESS WHEN YOU WORK ON HIGH SECTIONS. A
_______
 FALL CAN INJURE OR KILL YOU.

 CAUTION : DO NOT CAUSE DAMAGE TO THE SURFACES. THE COMPONENTS ARE MADE OF
_______
 CARBONFIBER REINFORCED PLASTIC.

 1.
 Reason for the Job

__________________
 Self Explanatory


 2.
 Job Set-up Information


______________________
 A. Fixtures, Tools, Test and Support Equipment
 -------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------

R 98D27903500000 2 PIN-SIDE STICK LOCKING B. Consumable Materials


 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 16-003  F ASNB70720
 COATING (OBSOLETE USE 16-021) (Ref. 20-31-00)
 
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM FLIGHT CONTROLS 飞行操纵9(16)