(b)
The aft static ports (S2) in the lower left pitot-static probe.
S 215-080
(9)
Examine the static ports for unwanted materials and rough locations on the inner and outer surfaces (Ref 34-11-01/601).
S 865-081
(10)
Remove the DO-NOT-CLOSE tags and close these circuit breakers:
(a) P6 Main Power Distribution Panel 1) 6D31 PROBE HEAT PITOT R 2) 6D32 PROBE HEAT AUX PITOT L 3) 6E01 PRIM T/E FLAP CONT AC 4) 6E02 PRIM T/E FLAP CONT DC
TASK 34-11-00-795-082
16. The Auxiliary No. 1 Static System Leak Test (Low-Range)
_______________________________________________________
A. Standard Tools and Equipment
(1)
Pneumatic Test Set
(a) Vacuum source, 10 to 30 inches of mercury (absolute)
(2)
Gages
(a) Static system test gage - required to indicate 10 to 30 inches of mercury (absolute) with accuracy of |0.1 (readable to |0.01) inch of mercury or |200 (readable to |20) feet.
(3)
Flow restrictors, control valves, cutoff valves, and pressure tape as required.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-00
ALL ú ú 02 Page 553 ú Feb 18/00
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
B. References
(1) 34-11-01/601, Pitot-Static Probe
C. Access
(1) Location Zone
115 Area Between Nose Gear Well and Fuselage, LH
116 Area Between Nose Gear Well and Fuselage, RH
117 Electrical and Electronics Compartment, LH
D. Procedure
S 865-299
WARNING: MAKE SURE THAT YOU DO NOT APPLY ELECTRICAL POWER TO THE FLIGHT
_______ CONTROLS. FLIGHT CONTROL SURFACES CAN MOVE AUTOMATICALLY WHEN YOU PRESSURIZE THE PITOT-STATIC SYSTEM. THIS CAN CAUSE INJURIES TO PERSONS AND DAMAGE TO EQUIPMENT.
CAUTION: MAKE SURE THAT YOU DO NOT APPLY ELECTRICAL POWER TO THE
_______ PITOT-STATIC PROBE HEATERS. YOU CAN CAUSE DAMAGE TO THE PITOT-STATIC PROBES.
(1) Open these circuit breakers and attach DO-NOT-CLOSE tags:
(a) P6 Main Power Distribution Panel
1) 6D30 PROBE HEAT PITOT L
2) 6D33 PROBE HEAT AUX PITOT R
3) 6E01 PRIM T/E FLAP CONT AC
4) 6E02 PRIM T/E FLAP CONT DC
S 485-500
WARNING: WHEN THE STATIC PORTS ARE COVERED, MAKE SURE THAT CONDITION IS
_______ VISIBLE FROM THE GROUND. FAILURE TO OBSERVE AND REMOVE COVERINGS OVER STATIC PORTS BEFORE FLIGHT MAY CAUSE LARGE ERRORS ON AIRSPEED SENSING AND ALTITUDE SENSING SIGNALS, WHICH MAY LEAD TO LOSS OF SAFE FLIGHT.
WARNING:_______MAKE SURE THAT THE PROBE HEAT IS NOT ON. YOU CAN CAUSE INJURY TO PERSONS.
CAUTION:_______DO NOT EXTEND THE SEALS INTO THE STATIC PORT. YOU CAN CAUSE DAMAGE TO THE SURFACE IN THE AREA WHEN YOU REMOVE THE SEALS.
(2) Seal these locations with vinyl adhesive tape:
(a) The forward static ports (S1) in the lower right pitot-static probe.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
34-11-00
ALL ú ú 02 Page 554 ú Feb 15/98
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
A
747-400
MAINTENANCE MANUAL
(b) The aft static ports (S2) in the upper left pitot-static probe.
S 485-085
(3) Connect the pneumatic test set to the test fitting of the auxiliary No. 1 static system.
(a)
Connect the static (vacuum) source in the pneumatic test unit through the static control valve to the static cutoff valve.
(b)
Connect the auxiliary No. 1 quick-disconnect test fitting to the static cutoff valve through the static system test gage and flow restrictor.
NOTE: You will find the test fitting on the left side of the
____ airplane above the drains at STA 400.
(c) Open the static cutoff valve.
S 795-086
(4) Do a leak test of the auxiliary No. 1 static system (low-range).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：747-400 AMM 飞机维护手册 导航 NAVIGATION 1(59)
