2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s) No specific safety barriers No specific spark-proof lamp No specific warning notice No specific access platform 2.5 m (8 ft. 2 in.) 98D27803000000 1 LOCKING TOOL - FLAP/SLAT CONTROL LEVER
R 1EFF : 301-399, 1 57-53-00Page A662 1 1 May 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1 57-53-00Page A663 1 1 May 01/05 1 1 1CES 1
INTENTIONALLY BLANK
R 1 1 57-53-00Page A664 1 1 May 01/05 1 1 1CES 1 B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 08-061A D DAN 220
ALUMINIUM FOIL ADHESIVE TAPE (Ref. 20-31-00) Material No. 11-026 GB DEF-STAN 68-148/1
SOLVENT GENERAL PURPOSE (Ref. 20-31-00) Material No. 19-003 USA AMS 3819
LINT-FREE COTTON CLOTH (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
27-50-00-866-008 Extension of the Flaps on the Ground 27-50-00-866-009 Retraction of the Flaps on the Ground 27-54-61-000-002 Removal of the Flap Kink-Seals 27-54-61-400-006 Installation of the Flap Kink-Seals ASRM 575221 (for corrective action) 57-53-00-991-027 Fig. 623
3. Job Set-up
__________
Subtask 57-53-00-941-080
A. Safety Precautions
(1)
Put a warning notice on the flap/slat control lever (panel 114VU) to tell persons not to operate the flaps.
(2)
Put the safety barriers in position.
Subtask 57-53-00-860-050
B. Aircraft Maintenance Configuration
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1) Fully extend the flaps (Ref. TASK 27-50-00-866-008).
1EFF : 301-399, 1 57-53-00Page A665 1 1 Nov 01/04R 1 1 1CES 1
(2) Make sure that the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) is installed on the flap/slat control lever on the panel 114VU.
Subtask 57-53-00-865-107
C. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
Subtask 57-53-00-010-074
D. Get Access
(1)
Put the access platform in position below the inboard rib of the outboard flap at zone 587(687).
(2)
Remove the flap kink-seals (Ref. TASK 27-54-61-000-002).
(3)
Remove and discard the inspection hole covers.
(4)
Put the spark-proof lamp adjacent to the inspection area.
4. Procedure
_________ (Ref. Fig. 623/TASK 57-53-00-991-027) CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING
_______
EDGE:
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-53-00-110-079
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the outboard double slotted flap inboard rib, including interconnection strut attachment bracket, lever and roller internal and external.
1EFF : 301-399, 1 57-53-00Page A666 1 1 Nov 01/04R 1 1 1CES 1
Outboard Flap - Inboard Rib - Inspection Area
Figure 623/TASK 57-53-00-991-027
1EFF : 301-399, 1 57-53-00Page A667 1 1 Nov 01/04R 1 1 1CES 1
Subtask 57-53-00-210-070
B. Detailed Visual Inspection of Outboard Double Slotted Flap Inboard Rib, Including Interconnection Strut Attachment Bracket, Lever and Roller, Internal and External, LH/RH
(1) Do an inspection of the rib, interconnection strut attachment bracket, lever and roller. Make sure that:
-
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼5(6)
