R 1EFF : 301-399, 1 57-55-00Page 405 1 1 May 01/04 1 1 1CES 1
R (h) Fully tighten the cable ties (3) that were loosely fitted, but
R not the cable tie guide at point 'X'. Make sure that you do not
R compress the electrical harnesses (9).
R (i) Disconnect the PTU (Ref. TASK 29-23-00-860-001).
R NOTE : The flaps will travel at half speed.____
R (j) Remove the TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER.
R (k) Do the operational test of flap system (Ref. TASK 27-54-00-710-
R 001). Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER
R (98D27803000000) on the flap/slat control lever at each flap
R position.
R (l) With the flaps at positions 1, 2, 3 and FULL, examine the
R electrical harnesses (9) and the interface connectors (6). Make
R sure that they are correctly attached and that they do not touch:
R - the flap drive gearbox (1)
R - the flap track beam (5)
R - the flap track carriage (2)
R - the adjacent structure.
R (m) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the
R flap/slat control lever.
R (n) Connect the PTU (Ref. TASK 29-23-00-860-002).
R (o) Remove the ground support and maintenance equipment, the special
R and standard tools and all other items.
R (p) After each flight, the electrical harnesses (9) and the interface
R connectors (6), must be examined to make sure that:
R - there is no damage to the electrical harnesses (9) or the cable
R ties (3)
R - there is no chafing of the electrical harnesses (9)
R - the interface connectors (6) are correctly attached and are not
R damaged.
R NOTE : It may be necessary to lubricate the deactivated____
R flap-track assembly (because of bad weather and the local
R conditions) (Ref. TASK 12-22-27-640-004).
R (q) Make a note in the aircraft log that the flap-track fairing has
R been deactivated.
R 1EFF : 301-399, 1 57-55-00Page 406 1 1 May 01/04 1 1 1CES 1R **ON A/C ALL
5. Close-up
________
Subtask 57-55-00-865-059
A. Make sure that this(these) circuit breaker(s) is(are) closed: 6CV, 8CV.
Subtask 57-55-00-942-050
B. Removal of Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the access platform(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
TASK 57-55-00-440-001
Reactivation of the Flap-Track Fairing
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the CDL TASK: 27-1
Flap Track Fairing
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers No specific warning notices No specific adjustable access platform 3.5 m (11 ft. 6 in.) 98D27803500001 1 TOOL-ZERO LOCKING, FLAP SLAT CTL LEVER
1EFF : ALL 1 57-55-00Page 408 1 1 May 01/04R 1 1 1CES 1
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION ------------------------------------------------------------------------------- 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320飞机维护手册 AMM WINGS 机翼5(44)
