-replace the defective sensor (Ref. TASK 32-31-73-000-001) and (Ref. TASK 32-31-73-400-001).
(i)
FOR 30GA, 31GA
-replace the defective sensor (Ref. TASK 32-31-73-000-005) and (Ref. TASK 32-31-73-400-005).
(j)
FOR 32GA, 33GA, 34GA, 35GA
-check the defective proximity sensor and (if necessary) adjust the target clearance (Ref. TASK 32-31-73-200-001) and (Ref. TASK 32-31-73-820-003)
- or replace the defective sensor (Ref. TASK 32-31-73-000-001) and (Ref. TASK 32-31-73-400-001).
(k) FOR 36GA, 37GA, 38GA, 39GA
-check the defective proximity sensor and (if necessary) adjust the target clearance (Ref. TASK 32-31-73-200-002) and (Ref. TASK 32-31-73-820-004)
- or replace the defective sensor (Ref. TASK 32-31-73-000-005) and (Ref. TASK 32-31-73-400-005).
(l)
FOR 5MJ, 12MJ
-replace the defective switch (Ref. TASK 52-35-13-000-002) and (Ref. TASK 52-35-13-400-002).
(m)
FOR 28WV, 34WV
-adjust the defective switch (Ref. TASK 52-71-00-820-004)
- or replace the defective switch (Ref. TASK 52-71-12-000-001) and (Ref. TASK 52-71-12-400-001).
1EFF : ALL 1 32-31-73Page A517 1 1 May 01/04R 1 1 1CES 1
(n) FOR 30WV, 32WV
-adjust the defective switch (Ref. TASK 52-71-00-820-003)
- or replace the defective switch (Ref. TASK 52-71-12-000-002) and (Ref. TASK 52-71-12-400-002).
Subtask 32-31-73-860-071
E. Aircraft Maintenance Configuration WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE FLIGHT CONTROLS ARE
_______ CLEAR. MOVEMENT OF FLIGHT CONTROLS CAN CAUSE INJURY TO PERSONS AND/OR DAMAGE.
(1)
Install the two LGCIUs (Ref. TASK 32-31-71-400-001).
(2)
If necessary, extend the landing gear (Ref. TASK 32-30-00-867-002).
(3)
If necessary, lower the aircraft off the jacks (Ref. TASK 07-11-00-586-002).
(4)
Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat control lever.
(5)
Fully retract the flaps (Ref. TASK 27-50-00-866-009).
5. Close-up
________ Subtask 32-31-73-942-063
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the NLG doors (Ref. TASK 32-22-00-410-001).
(3)
Close the MLG doors (Ref. TASK 32-12-00-410-001).
(4)
Remove the safety barriers.
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(6)
Remove the warning notice(s).
1EFF : ALL 1 32-31-73Page A518 1 1 May 01/04R 1 1 1CES 1
PROXIMITY SENSOR - INSPECTION/CHECK
___________________________________
TASK 32-31-73-200-001
Inspection of the MLG Proximity Sensor and Target Clearances
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
R NOTE : This procedure is for proximity sensors 14GA, 15GA, 16GA, 17GA, 20GA,
____ R 21GA, 22GA, 23GA, 32GA, 33GA, 34GA and 35GA only.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
No specific access platform 2 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-581-001 Lifting for Aircraft Maintenance Operations 07-11-00-586-002 Lowering of the Aircraft for Maintenance Operations 24-41-00-862-002 De-energize the Aircraft Electrical Circuits Supplied
from the External Power 32-00-00-481-001 Installation of the Safety Devices on the Landing
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架5(87)
