1EFF : ALL 1 32-33-00Page 553 1 1 Aug 01/05 1 1 1CES 1
R MLG-Bay Cable-Tension Graph - Weight on Wheels Figure 509/TASK 32-33-00-991-015
1EFF : 1 1 1CES ALL 1 111 32-33-00 Page 554 Aug 01/05
R R MLG-Bay Cable-Tension Graph - Weight on Jacks Figure 510/TASK 32-33-00-991-024
1EFF : 1 1 1CES ALL 1 111 32-33-00 Page 555 Aug 01/05
R (Ref. Fig. 510/TASK 32-33-00-991-024)
R R R (5) Operate the tensiometer. If necessary, adjust the turnbuckle body (17) until the tensiometer shows the same value as you found on the graph.
R (6) Release the tensiometer.
R (7) Operate the tensiometer. If you do not get the correct value, adjust the turnbuckle (17) again, until the value is correct.
R R (8) Safety the ends of the cables (5) and (6) and the turnbuckle body (17) with the two locking clips (16).
R R R R NOTE : If necessary, increase the cable tension to align the locking____ clips (16) and the turnbuckle body (17). Do not decrease the cable tension to align the locking clips (16) and the turnbuckle body (17).
(9) Remove the tensiometer.
Subtask 32-33-00-820-057
E. Adjustment of the cables (7) and (8)
(1) Do the same procedure as for cables (5) and (6), specified in paragraph 4. D.
Subtask 32-33-00-820-058
R R F. Adjustment of the cables (9) and (10) (Ref. Fig. 509/TASK 32-33-00-991-015, 510/TASK 32-33-00-991-024)
R R (1) Attach the tensiometer to the cable (9) at position B in the MLG-Bay, zone 191(192). Make sure that the tensiometer is attached a minimum of 80 mm (3.1496 in.) away from pulleys and turnbuckles.
(2) Make sure of the ambient temperature.
(3) Remove the two locking clips (16) from the turnbuckle body (17) between the cables (9) and (10).
1EFF : ALL 1 32-33-00Page 556 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-33-00Page 557 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-33-00-942-056
R R R R R (4) Find the correct tension value on the graph for the ambient temperature: - for Weight on Wheels (Ref. Fig. 509/TASK 32-33-00-991-015) - for Weight on Jacks. (Ref. Fig. 510/TASK 32-33-00-991-024)
R R R (5) Operate the tensiometer. If necessary, adjust the turnbuckle body (17) until the tensiometer shows the same value as you found on the graph.
R (6) Release the tensiometer.
R (7) Operate the tensiometer. If you do not get the correct value, adjust the turnbuckle (17) again, until the value is correct.
R R (8) Safety the ends of the cables (9) and (10) and the turnbuckle body (17) with the two locking clips (16).
R R R R NOTE : If necessary, increase the cable tension to align the locking____ clips (16) and the turnbuckle body (17). Do not decrease the cable tension to align the locking clips (16) and the turnbuckle body (17).
(9) Remove the tensiometer.
Subtask 32-33-00-820-059
G. Adjustment of the cables (11) and (12)
(1) Do the same procedure as for the cables (9) and (10), specified in paragraph 4. F.
Subtask 32-33-00-080-055
H. Removal of the Rigging Pins (Ref. Fig. 505/TASK 32-33-00-991-013)
(1) Remove the RIGGING PIN at position Pin 12 and Pin 1.
(2) Remove the RIGGING PIN at position Pin 2 and Pin 11.
J. Removal of Equipment
(1) On the panel 110VU, remove the wedges from the GRAVITY GEAR EXTN handle (18).
Subtask 32-33-00-865-060
K. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1GA, 2GA, 52GA.
Subtask 32-33-00-710-053
L. Free Fall Extension System Operation CAUTION : MAKE SURE THAT THE RIGGING PINS ARE REMOVED BEFORE OPERATION OF
_______ THE FREE FALL SYSTEM. DAMAGE WILL OCCUR IF THE RIGGING PINS ARE INSTALLED DURING SYSTEM OPERATION.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架5(110)
