2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-53-00-740-003 BITE Test of the ADF
AMM 34-57-22-000-002 Removal of the VOR/ADF/DME RMI (21FN)
AMM 34-57-22-400-002 Installation of the VOR/ADF/DME RMI (21FN)
ASM 34-53/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the ADF (system 1) (Ref. AMM TASK 34-53-00-740-003).
4. Fault Isolation
_______________
A. If the test gives the maintenance message
DMC1/2/3 (1WT1/2/3)/DDRMI (1FN)/ADF1 (2RP1):
- replace the RMI-VOR/ADF/DME (21FN) (Ref. AMM TASK 34-57-22-000-002) and (Ref. AMM TASK 34-57-22-400-002).
(1) If the fault continues:
- remove the VOR/ADF/DME RMI
- do a check and repair the wiring between the VOR/ADF/DME RMI and the first terminal block: for pins A/18 and 19 of the VOR/ADF/DME RMI (Ref. ASM 34-53/01)
- install the VOR/ADF/DME RMI.
B. Do the test given in para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 106-149, 201-299, 301-399, 401-499, ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 253
Aug 01/05 CESR **ON A/C 001-049, 051-051, 053-099, 101-149, 151-199, 201-299, 301-399, R 401-499,
TASK 34-53-00-810-828
Loss of the ADF2 Data
1. Possible Causes
_______________
- RECEIVER-ADF, 2 (2RP2)
- wiring from the ADF receiver 2 to the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-53-00-740-003 BITE Test of the ADF
AMM 34-53-31-000-002 Removal of the ADF Receiver (2RP1, 2RP2)
AMM 34-53-31-400-002 Installation of the ADF Receiver (2RP1, 2RP2)
ASM 34-53/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the ADF (system 2) (Ref. AMM TASK 34-53-00-740-003).
4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC1/2/3 (1WT1/2/3)/DDRMI (1FN)/ADF2 (2RP2):
- swap the RECEIVER-ADF, 2 (2RP2) and the ADF receiver 1 (Ref. AMM TASK 34-53-31-000-002) and (Ref. AMM TASK 34-53-31-400-002).
(1) If the fault stops:
- replace the ADF receiver that you installed on side 1.
(2) If the fault continues:
- remove the ADF receiver 2
- do a check and repair the wiring from the ADF receiver 2 to the first terminal block: for pins AB/13B, 14B of the ADF receiver 2 (Ref. ASM 34-53/01)
- install the ADF receiver 2.
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1R EFF : 001-049, 051-051, 053-099, 101-149, ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 254
151-199, 201-299, 301-399, 401-499, Aug 01/05 CES Loss of the ADF2 Display on the CAPT ND Only
1. Possible Causes
_______________
- DMC-1 (1WT1)
- DMC-3 (1WT3)
- wiring between the DMC1 and the first terminal block
- wiring between the DMC3 and the first terminal block
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 31-63-34-000-001 Removal of the DMC (1WT1,1WT2,1WT3)
AMM 31-63-34-400-001 Installation of the DMC (1WT1,1WT2,1WT3)
AMM 34-53-00-740-003 BITE Test of the ADF
ASM 34-53/01
3. Fault Confirmation
__________________
A. Test Do the BITE test of the ADF (system 2) (Ref. AMM TASK 34-53-00-740-003).
NOTE : Do the test with the EIS DMC selector switch (18WT) on the
____
SWITCHING panel (8VU) at NORM then at CAPT/3.
4. Fault Isolation
_______________
A. If the test gives the maintenance message DMC1/2/3 (1WT1/2/3)/DDRMI
(1FN)/ADF2 (2RP2) with the EIS DMC selector switch at NORM only:
- replace the DMC-1 (1WT1) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001). 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 Trouble Shooting Manual 排故手册 导航 NAVIGATION 3(139)
