(2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 1 INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-53/01).
C. If on the F/O ND only: . the ADF 1 data do not come into view . the red flag is shown:
- make sure that on the center pedestal, on the SWITCHING panel 8VU, the EIS DMC selector switch is at F/O 3:
(1) If no:
- replace the DMC-2 (1WT2) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 1 INPUT bus from the DMC 2 (1WT2) to the first terminal block (Ref. ASM 34-53/01).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 239
May 01/05R
CES (2) If yes:
- replace the DMC-3 (1WT3) (Ref. AMM TASK 31-63-34-000-001) and (Ref. AMM TASK 31-63-34-400-001).
(a) If the fault continues:
- do a check and repair the wiring of the ADF 1 INPUT bus from the DMC 3 (1WT3) to the first terminal block (Ref. ASM 34-53/01).
D. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 240
May 01/05R
CES Loss of the ADF 1 Data on the ND
1. Possible Causes
_______________
- RECEIVER-ADF, 1 (2RP1)
- ANTENNA-ADF LOOP AND SENSE, 1 (3RP1)
- wiring from the ADF loop and sense antenna 1 (3RP1) to the ADF receiver 1 (2RP1)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 34-53-00-710-002 Operational Test of the ADF
AMM 34-53-00-740-003 BITE Test of the ADF
AMM 34-53-11-000-001 Removal of the ADF Loop and Sense Antenna
AMM 34-53-11-400-001 Installation of the ADF Loop and Sense Antenna
AMM 34-53-31-000-002 Removal of the ADF Receiver (2RP1, 2RP2)
AMM 34-53-31-400-002 Installation of the ADF Receiver (2RP1, 2RP2)
ASM 34-53/01
3. Fault Confirmation
__________________
A. Test
(1) Do the operational test of the ADF (Ref. AMM TASK 34-53-00-710-002).
4. Fault Isolation
_______________
A. If the ADF 1 data do not come into view on the ND:
- do the BITE test of the ADF (Ref. AMM TASK 34-53-00-740-003).
(1) If the test gives a maintenance message:
- Do the trouble shooting procedure related to the maintenance message.
(2) If the test does not give a maintenance message:
- replace the RECEIVER-ADF, 1 (2RP1) (Ref. AMM TASK 34-53-31-000-002) and (Ref. AMM TASK 34-53-31-400-002).
(a) If the fault continues:
- replace the ANTENNA-ADF LOOP AND SENSE, 1 (3RP1) (Ref. AMM TASK 34-53-11-000-001) and (Ref. AMM TASK 34-53-11-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 241
May 01/05R CES
1_ If the fault continues:
- do a check and repair the wiring from the ADF loop and sense
antenna 1 (3RP1) to the ADF receiver 1 (2RP1) (Ref. ASM 34-
53/01).
B. Do the test given in Para. 3.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞34-53-00∞∞∞∞∞∞∞∞∞∞Page 242
May 01/05R
CES ADF 2 System Inoperative
1. Possible Causes
_______________
- RECEIVER-ADF, 2 (2RP2)
- DMC-1 (1WT1)
- DMC-3 (1WT3)
- DMC-2 (1WT2)
- wiring of the BEARING OUTPUT 2 bus from the ADF receiver 2 (2RP2) to the first terminal block
- wiring of the ADF 2 INPUT bus from the DMC 1 (1WT1) to the first terminal block
- wiring of the ADF 2 INPUT bus from the DMC 3 (1WT3) to the first terminal block 中国航空网 www.aero.cn 航空翻译 www.aviation.cn 本文链接地址：A320 Trouble Shooting Manual 排故手册 导航 NAVIGATION 3(135)
