3. Fault Confirmation
__________________
A. Do the operational test of the Logo Lights (Ref. AMM TASK 33-47-00-710-002).
4. Fault Isolation
_______________
A. If the test shows that the two LOGO LIGHTS 3LY (4LY) do not go off:
- make sure that the NAV LOGO switch 3LA is set to the OFF position.
(1) If the fault continues:
- Open CB 2LR.
(a) If the fault continues:
- replace RELAY 5LY
(Ref. ASM 33-47/01).
(b) If both LOGO LIGHTS 3LY and 4LY go off:
- check and replace if necessary RELAY 6LA and RELAY 7LA (Ref. ASM 33-41/01).
B. Do the test as given in the Para. 3. A.
5. Close-up
________
A. Put the aircraft back to its initial configuration.
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞33-47-00∞∞∞∞∞∞∞∞∞∞Page 208
Feb 01/98 CES
LOGO LIGHTS - TASK SUPPORTING DATA
__________________________________
1. General
_______ (Ref. Fig. 301) The logo lights are installed to give illumination to the airlines emblem (logo), which is marked on each side of the vertical fin. They come on in conjunction with the navigation lights.
Logo Lights - Block Diagram
Figure 301
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞33-47-00∞∞∞∞∞∞∞∞∞∞Page 302
Feb 01/98 CES
ANTI-COLLISION/STROBE LIGHTING - FAULT ISOLATION PROCEDURES
___________________________________________________________
TASK 33-48-00-810-801
Strobe Lights - None of the Anti-Collision Strobe Lights flash
1. Possible Causes
_______________
- wiring
- PWR SPLY-RELAY 12LV
- LT-STROBE SW 11LV
- LGD SIGNAL-RELAY 13LV
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
AMM 33-48-00-710-002 Operational Test of the Anti-Collision/Strobe
Lighting ASM 33-48/01 TSM 33-48-00-810-802 Strobe Lights - One of the Anti-Collision Strobe
Lights does not flash
3. Fault Confirmation
__________________
A. Do the operational test of the Anti-Collision / Strobe Lighting and confirm that none of the strobe lights flash (Ref. AMM TASK 33-48-00-710-002).
4. Fault Isolation
_______________
A. If the test confirms the fault: R - do a check for 115 VAC at the related PWR SPLY UNIT connector A/1, A/2 R and A/3 (Ref. ASM 33-48/01).
R (1) If there is approx. 115 VAC:
- do the trouble shooting procedures for One of the Anti-Collision Strobe Lights does not flash (Ref. TSM TASK 33-48-00-810-802).
R (2) If there is no 115 VAC:
R - do a check for 115 VAC at the PWR SPLY-RELAY 12LV connector A/A1,
R A/B1 and A/C1 (Ref. ASM 33-48/01).
R (a) If there is approx. 115 VAC:
- do a check and repair the wiring between: PWR SPLY-RELAY 12LV conn. A/A1 and related PWR SPLY UNIT conn. A/1,
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞33-48-00∞∞∞∞∞∞∞∞∞∞Page 201
May 01/04 CES (3) If the fault continues:
PWR SPLY-RELAY 12LV conn. A/B1 and related PWR SPLY UNIT conn.
A/2,
PWR SPLY-RELAY 12LV conn. A/C1 and related PWR SPLY UNIT conn.
A/3,
PWR SPLY-RELAY 12LV conn. A/X1 and LT-STROBE SW 11LV conn. A2,
PWR SPLY-RELAY 12LV conn. A/X2 and LT-STROBE SW 11LV conn. 1A
(Ref. ASM 33-48/01).
R (b) If there is no 115 VAC:
R - do a check for 115 VAC at the PWR SPLY-RELAY 12LV connectors
R A/A2, A/B2 and A/C2 (Ref. ASM 33-48/01).
R 1_ If there is no 115 VAC:
- do a check and repair the wiring between:
CB 10LV conn. A2 and PWR SPLY-RELAY 12LV conn. A/A2,
CB 10LV conn. B2 and PWR SPLY-RELAY 12LV conn. A/B2,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 LIGHTS 灯光(69)
