「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞33-26-00∞∞∞∞∞∞∞∞∞∞Page 308
Aug 01/05 CESR Block Diagram - Lavatory Lighted Signs R Figure 301C (SHEET 2)
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : 401-499, ∞∞33-26-00∞∞∞∞∞∞∞∞∞∞Page 309
Aug 01/05 CES
LIGHT - WORK, CABIN ATTENDANT - FAULT ISOLATION PROCEDURES
__________________________________________________________
TASK 33-27-00-810-801
Cabin Attendant Work Light Fault
1. Possible Causes
_______________
- WORK LIGHT
- lamp
- PUSHBUTTON SWITCH
- wiring
- PWR UNIT
- FAP (120RH)
- PWR SPLY RELAY (2LZ)
2. Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
AMM 23-73-00-740-003 BITE Test of the Cabin Intercommunication Data System
(CIDS) through the PTP
AMM 23-73-15-000-001 Removal of the Light Module 122RH
AMM 23-73-15-400-001 Installation of the Light Module 122RH
AMM 33-27-00-710-001 Operational Test of the Cabin Attendant Work-Light
AMM 33-27-12-000-001 Removal of the Cabin Attendant Work-Lights
AMM 33-27-12-400-001 Installation of the Cabin Attendant Work-Lights
AMM 33-27-38-000-001 Removal of the Power Unit for the Cabin Attendant
Work-Light
AMM 33-27-38-400-001 Installation of the Power Unit for the Cabin
Attendant Work-Light
ASM 33-27/01
3. Fault Confirmation
__________________
A. Do the operational test of the cabin-attendant work lights (Ref. AMM TASK 33-27-00-710-001).
B. Do the CIDS BITE test (Ref. AMM TASK 23-73-00-740-003).
4. Fault Isolation
_______________
A. If the operational test gives the maintenace message WORK LIGHT FWD 1,2,L,R or WORK LIGHT MID 1,2,L,R or WORK LIGHT AFT 1,2,L,R:
- replace the related WORK LIGHT (Ref. AMM TASK 33-27-12-000-001) and (Ref. AMM TASK 33-27-12-400-001).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞33-27-00∞∞∞∞∞∞∞∞∞∞Page 201
Feb 01/98 CES (1) If the fault continues:
- replace the related PWR UNIT (Ref. AMM TASK 33-27-38-000-001) and (Ref. AMM TASK 33-27-38-400-001).
B. If the operational test gives the maintenace message WORK LIGHT PCB FWD 1,2,L,R or WORK LIGHT PCB MID 1,2,L,R or WORK LIGHT PCB AFT 1,2,L,R:
- replace the related WORK LIGHT (Ref. AMM TASK 33-27-12-000-001) and (Ref. AMM TASK 33-27-12-400-001).
(1) If the fault continues:
- replace the related PWR UNIT (Ref. AMM TASK 33-27-38-000-001) and (Ref. AMM TASK 33-27-38-400-001).
C. If the operational test gives the maintenace message POWER PCB FWD 1,2,L,R or POWER PCB 1,2,L,R or POWER PCB AFT 1,2,L,R:
- replace the related PWR UNIT (Ref. AMM TASK 33-27-38-000-001) and (Ref.
AMM TASK 33-27-38-400-001). R
R D. If the test gives a different maintenance message, do the trouble R shooting procedure related to the maintenance message.
E. If the operational test gives no maintenance message, but one of the work lights does not come on:
- replace the related lamp (Ref. AMM TASK 33-27-12-000-001) and (Ref. AMM TASK 33-27-12-400-001).
(1) If the fault continues:
- do a check of the related PUSHBUTTON SWITCH and replace it if necessary.
(2) If the fault continues:
- replace the related PWR UNIT (Ref. AMM TASK 33-27-38-000-001) and (Ref. AMM TASK 33-27-38-400-001).
(3) If the fault continues:
- do a check and repair the wiring between: PWR UNIT (3LZ) conn. A/D and L FWD ATTND SEAT (2063VU1) pin 1, PWR UNIT (3LZ) conn. A/G and L FWD ATTND SEAT (2063VU1) pin 3, GND and L FWD ATTND SEAT (2063VU1) pin 2, PWR UNIT (13LZ) conn. A/F and R AFT ATTND SEAT (2062VU2) pin 1, GND and R AFT ATTND SEAT (2062VU2) pin 2, PWR UNIT (12LZ) conn. A/F and L AFT ATTND SEAT (2062VU1) pin 1, GND and L AFT ATTND SEAT (2062VU1) pin 2 (Ref. ASM 33-27/01).
「一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一一1 EFF : ALL ∞∞33-27-00∞∞∞∞∞∞∞∞∞∞Page 202
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320 Trouble Shooting Manual 排故手册 LIGHTS 灯光(49)
