R 1EFF : 051-099, 1 32-41-12Page 413 1 1 May 01/05 1 1 1CES 1 1EFF : ALL 1 32-41-12Page 414 1 1 May 01/05 1 1 1CES 1R **ON A/C ALL
R (3) Engage the drive dog (13) in the fork of the rotating mechanism.
R (4) Install the screws (14), the washers (15).
R (5) TORQUE the screws (14) to between 0.4 and 0.51 m.daN (35.39 and 45.13
R lbf.in) and safety them with corrosion resistant steel lockwire 0.8mm
R (0.032 in) dia.
R **ON A/C ALL
Subtask 32-41-12-860-051
D. Aircraft Maintenance Configuration
(1) Inflate the tire to the unloaded pressure (Ref. TASK 12-14-32-614-
001).
(2) Lower the aircraft on its wheels (Ref. TASK 07-12-00-582-001).
(3) Make sure that the pressure of the tire is correct (Ref. TASK 32-41-
00-210-003).
R **ON A/C 051-099,
R Subtask 32-41-12-865-052
R E. Make sure that this(these) circuit breaker(s) is(are) closed:
R 1GV
R Subtask 32-41-12-720-050
R F. Do the functional test of the tire pressure indicating system (Ref. TASK
R 32-49-00-720-001).
5. Close-up
________
Subtask 32-41-12-942-051
A. Removal of the Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
1EFF : ALL 1 32-41-12Page 415 1 1 May 01/05 1 1 1CES 1
TASK 32-41-12-000-002 Removal of the Axle Sleeve
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-12-000-001 Removal of the NLG Wheel (2659GM,2660GM) 32-41-12-991-002 Fig. 402
3. Job Set-up
__________ Subtask 32-41-12-010-050
A. Get access
(1) Remove the related landing gear wheel (Ref. TASK 32-41-12-000-001).
4. Procedure
_________ (Ref. Fig. 402/TASK 32-41-12-991-002) Subtask 32-41-12-020-051
A. Removal of the Axle Sleeve
(1)
Remove the retaining ring (3).
(2)
Remove the axle sleeve (2).
1EFF : ALL 1 32-41-12Page 416 1 1 May 01/05 1 1 1CES 1
Axle Sleeve
Figure 402/TASK 32-41-12-991-002
1EFF : ALL 1 32-41-12 Page 417
1 1 May 01/05
1 1
1CES 1
TASK 32-41-12-400-002 Installation of the Axle Sleeve
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-022 USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 11-002 USA MIL-PRF-680 DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT) (Ref. 20-31-00)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-41-12-400-001 Installation of the NLG Wheel (2659GM,2660GM)
3. Job Set-up
__________ Subtask 32-41-12-640-052
A. Preparation for Installation
(1)
Clean the axle (1) with CLEANING AGENTS (Material No. 11-002). Dry it with filtered compressed air .
(2)
Lightly lubricate the axle (1) and the axle protective sleeve (2) with COMMON GREASE (Material No. 04-022).
1EFF : ALL 1 32-41-12Page 418 1 1 May 01/05 1 1 1CES 1
4. Procedure
_________ Subtask 32-41-12-420-051
A. Installation of the Axle Sleeve
(1)
Install the axle sleeve (2).
(2)
Install the retaining ring (3).
5. Close-up
________ Subtask 32-41-12-410-050
A. Close access
(1)
Install the related wheel (Ref. TASK 32-41-12-400-001).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(81)
