(2)
Remove the hubcap (11). NOTE : Remove the hubcap along the centerline of the wheel axle to
____ prevent damage to the tachometer drive shaft.
Subtask 32-41-11-020-068
B. Removal of the Wheel WARNING : BE CAREFUL WHEN YOU REMOVE/INSTALL THE WHEEL AND TIRE ASSEMBLY
_______ TO PREVENT INJURY TO PERSONS AND/OR DAMAGE TO THE WHEEL, AXLE OR OTHER EQUIPMENT. THE ASSEMBLY IS VERY HEAVY (BETWEEN 130 KG AND 200 KG (290 LBS AND 440 LBS)).
CAUTION : MAKE SURE THAT THE AXLE THREAD PROTECTOR IS CORRECTLY INSTALLED
_______ ON THE AXLE. YOU CAN CAUSE DAMAGE TO THE AXLE SLEEVE WHEN YOU REMOVE/INSTALL A WHEEL IF THE AXLE THREAD PROTECTOR IS: -NOT USED. -NOT FULLY ENGAGED ON THE AXLE.
(1)
Remove and discard the cotter pin (4).
(2)
Remove the nuts (5), the washers (6) and the bolts (8).
(3)
Remove the axle nut (7) with the ADAPTOR MLG (H47682).
(4)
Install the PROTECTOR (F46754-1000).
(5)
Apply a thin layer of COMMON GREASE (Material No. 04-004A) on the axle protector.
(6)
Remove the wheel (1)
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 403 1 1 Config-1 May 01/05 1 1 1CES 1
Main Gear Wheel
Figure 401/TASK 32-41-11-991-010
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 404 1 1 Config-1 May 01/05 1 1 1CES 1 TASK 32-41-11-400-006
Installation of the MLG Wheel (2649GM,2650GM,2651GM,2652GM)
WARNING : YOU MUST NOT PUT TOO MUCH GREASE ON THE AXLE SLEEVE. A VERY HOT BRAKE
_______
CAN CAUSE THE GREASE TO BURN AND CAUSE A FIRE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
R No specific Torque Wrench : range 0.00 to 1.20 m.daN R (0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) No specific Torque Wrench : range 6.00 to 36.00 m.daN
(50.00 to 260.00 lbf.ft) H47682 1 ADAPTOR MLG
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 04-003 USA MIL-T-5544 GRAPHITED PETROLATUM THREAD COMPOUND (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-035
SYNTHETIC WHEEL BEARING GREASE (Ref. 20-31-00)
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 405 1 1 Config-1 May 01/05 1 1 1CES 1
C. Expendable Parts -------------------------------------------------------------------------------
FIG.ITEM --------- |DESIGNATION ---------------------------------------- |IPC-CSN------------------------------
4 cotter pins 32-11-13 01E-200
4 cotter pins 32-11-13 01G-200
D. Referenced Information
------------------REFERENCE -------------------------------DESIGNATION ------------------------------
-------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 29-10-00-863-002 Pressurize the Yellow Hydraulic System 32-41-00-210-003 Inspection/Check of the Pressure of Tires 32-41-00-910-001 Tire Mixability Precautions 32-42-27-000-001 Removal of the Brake (2641GM,2642GM,2643GM,2644GM) 32-42-27-400-001 Installation of the Brake
(2641GM,2642GM,2643GM,2644GM) 32-41-11-991-010 Fig. 401
3. Job Set-up
__________
Subtask 32-41-11-941-077
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position in the cockpit to tell persons not to operate the landing gear.
(3)
Make sure that the wheel chocks are in position.
R 1EFF : 001-049, 101-149, 151-199, 201-299, 1 32-41-11Page 406 1 1 Config-1 May 01/05 1 1 1CES 1 Subtask 32-41-11-860-086
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(66)
