(2)
Put match marks on the cables before you loosen them.
(3)
Loosen the turnbuckles (31) from the cables (32) and (33).
(4)
Remove the cables from the pulley assembly (34).
4. Procedure
_________
(Ref. Fig. 402/TASK 32-33-17-991-002) Subtask 32-33-17-350-050
A. Replacement of the Shear-Pins
(1)
Turn the pulley assembly (34) so that the shear-pins are accessable.
(2)
Remove and discard the cotter pins (35).
(3)
Remove the castellated nuts (36) the washers (37) and the bolts (40).
1EFF : ALL 1 32-33-17Page 413 1 1 Feb 01/98 1 1 1CES 1
Pulley Assembly
Figure 402/TASK 32-33-17-991-002- 12 (SHEET 1)
1EFF : ALL 1 32-33-17 Page 414
1 1 Feb 01/98
1 1
1CES 1
Pulley Assembly
Figure 402/TASK 32-33-17-991-002- 22 (SHEET 2)
1EFF : ALL 1 32-33-17 Page 415
1 1 Feb 01/98
1 1
1CES 1
(4)
Remove the lock plates (38).
(5)
Remove the top half of the shear-pins (39).
(6)
Use a parallel pin punch and push the sheared-off part of the shear-pins through the pulley assembly (34).
(7)
Remove the debris from the pulley assembly (34).
(8) Clean the pulley assembly (34) and the adjacent area. R (9) Apply COMMON GREASE (Material No. 04-024B) to the new shear-pins (39)
(10)
Make sure that the shear-pin holds in the pulley assembly (34) and in the pulleys (41) are in line.
(11)
Install the shear-pins (39).
(12)
Put the lock plates (38) in position.
(13)
Install the bolts (40) the washers (37) and the castelled nuts (36) and lock them with cotter-pin (24).
(14)
Install and adjust the MLG free-fall extension cables (32) and (33) on the pulley assembly (34) (Ref. Fig. 402/TASK 32-33-17-991-002)
(a)
Put the cables (32) and (33) in position in the pulley assembly (34).
(b)
Connect each cable to its related cable with the turnbuckles (31)
(c)
Temporarily attach the locking pins (30).
(d)
Adjust the free-fall extension cables (Ref. TASK 32-33-00-820-003).
(e)
Do a cable tension check on the free-fall extension cables that were loosened (Ref. TASK 32-33-00-200-001).
Subtask 32-33-17-720-051
B. Test
(1) Do a functional test of the free-fall extension system. (Ref. TASK 32-33-00-720-001)
1EFF : ALL 1 32-33-17Page 416 1 1 May 01/01 1 1 1CES 1
5. Close-up
________ Subtask 32-33-17-410-051
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Do the applicable steps that follow:
(a)
Install the cabin floor panel 242FF (Ref. TASK 53-32-12-400-002).
(b)
Install the cabin floor covering (Ref. TASK 25-28-41-400-001).
(c)
Install the passenger seats that were removed (Ref. TASK 25-21-41-400-001).
Subtask 32-33-17-942-051
B. Put the system back to the serviceable condition.
(1)
Remove the warning notice(s).
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
Subtask 32-33-17-862-051
C. Energize the ground service network
(Ref. TASK 24-42-00-862-001)
1EFF : ALL 1 32-33-17Page 417 1 1 Feb 01/98 1 1 1CES 1 WHEELS AND BRAKES - DESCRIPTION AND OPERATION
_____________________________________________
1. General
_______
A. Tires, Wheels, Brakes The main gear wheels have multidisc carbon brakes that two sets of independently supplied pistons operate; the Green hydraulic system supplies one set, the Yellow hydraulic system supplies the other set with the aid of one brake Yellow pressure accumulator. Each brake has automatic adjusters, two wear pin indicators and a temperature sensor. The main gear wheels include fusible plugs which protect the wheel and the tire against burst if an overheat occurs. The wheels have radial tires.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(34)
