(2)
Make sure that the PARKING BRK control-switch is set to OFF before you do this procedure.
CAUTION : MAKE SURE THAT ALL THE PISTONS OF THE BRAKE ARE IN THE
_______
RELEASED POSITION.
(3) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
1EFF : ALL 1 32-42-00Page 418 1 1 May 01/04R 1 1 1CES 1
Subtask 32-42-00-865-057
C. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
4. Procedure
_________
(Ref. Fig. 403/TASK 32-42-00-991-004) Subtask 32-42-00-040-054
A. Deactivation with isolation of the Green hydraulic supply
(1)
Loosen the knurled sleeve (2) of the Green half-coupling (1). Turn and disconnect the coupling.
(2)
Clean the knurled sleeve (2). Apply 2 or 3 turns of the self-adhesive fabric tape (20 mm (0.7874 in.) to 30 mm (1.1811 in.)) to the sleeve (1).
(3)
Tightly wind 3 or 4 turns of the corrosion resistant steel lockwire dia 0.8 mm around the middle of the sleeve (2) with the tape.
(4)
Twist the lockwire and put it through the nearest locking hole you can get access to in the hexagonal head of the fixed half-coupling (1). Tighten the lockwire and twist it.
(5)
Remove the bleed screw plug (4) from the bleed screw (3).
(6)
Connect a vinyl hose to the related bleed screw and put the other end in a container that contains HYDRAULIC FLUIDS (Material No. 02-003).
(7)
Slowly loosen the bleed screw (3) to release hydraulic residual pressure from the brake.
(8)
Tighten the bleed screw (3).
(9)
Disconnect the vinyl hose.
(10) Install the bleed screw plug (4) on the bleed screw.
1EFF : ALL 1 32-42-00Page 419 1 1 May 01/04R 1 1 1CES 1
Normal Brake Deactivation Figure 403/TASK 32-42-00-991-004
1EFF : 1 1R 1CES ALL 1 11 1 32-42-00 Page 420 May 01/04
Subtask 32-42-00-910-053
B. Precaution CAUTION : MAKE SURE THAT THE LOCKWIRE CANNOT WEAR DURING THE OPERATIONS
_______
OF THE LANDING GEAR.
Subtask 32-42-00-860-073
C. Aircraft Maintenance Configuration
(1)
Pressurize the Green hydraulic system from the Yellow hydraulic system through the PTU with the electric pump (Ref. TASK 29-23-00-863-001).
(2)
On the panel 402VU, make sure that the A/SKID & NOSE WHEEL switch is set to ON.
Subtask 32-42-00-710-058
D. Test
(1) Do this test:
-------------------------------------------------------------------------------ACTION RESULT -------------------------------------------------------------------------------
1.
Push in fully the related brake Make sure that there are no leaks on
pedals and hold them pushed in. the hydraulic-pressure line you
disconnected.
2.
Release the brake pedals.
5. Close-up
________ Subtask 32-42-00-860-075
A. Put the aircraft back to its initial configuration.
(1)
Depressurize the Green hydraulic system (Ref. TASK 29-10-00-864-001).
(2)
Make sure that the level of the hydraulic fluid is correct in the Green hydraulic reservoir. Add some hydraulic fluid if it is necessary.
1EFF : ALL 1 32-42-00Page 421 1 1 May 01/04R 1 1 1CES 1
(3)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
(4)
Remove the warning notice(s).
(5)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
(6)
In the cockpit, install a temporary placard to tell the crew that the normal braking on the wheel 1 (2, 3, 4) is not operational.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(121)
