(6)
Remove the wheel (1).
1EFF : 051-099, 1 32-41-11Page 405 1 1 Config-3 May 01/05 1 1 1CES 1 TASK 32-41-11-400-006-B
Installation of the MLG Wheel (2649GM,2650GM,2651GM,2652GM)
WARNING : YOU MUST NOT PUT TOO MUCH GREASE ON THE AXLE SLEEVE. A VERY HOT BRAKE
_______ CAN CAUSE THE GREASE TO BURN AND CAUSE A FIRE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft) No specific Torque Wrench : range 0.20 to 3.60 m.daN
(2.00 to 26.00 lbf.ft) No specific Torque Wrench : range 1.00 to 10.00 m.daN
(8.00 to 75.00 lbf.ft) No specific Torque Wrench : range 2.00 to 20.00 m.daN
(15.00 to 150.00 lbf.ft) No specific Torque Wrench : range 6.00 to 36.00 m.daN
(50.00 to 260.00 lbf.ft) H47682 1 ADAPTOR MLG MG174-04 1 DISASSEMBLY TOOL
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
No specific corrosion resistant steel lockwire dia 0.8 mm (0.03 in.) Material No. 04-003 USA MIL-T-5544 GRAPHITED PETROLATUM THREAD COMPOUND (Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2 SYNTHE.HYDROCARBON GREASE HIGH PRESSURE (Ref. 20-31-00)
Material No. 04-035 SYNTHETIC WHEEL BEARING GREASE (Ref. 20-31-00)
1EFF : 051-099, 1 32-41-11Page 406 1 1 Config-3 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
Material No. 11-002 USA MIL-PRF-680
DRY CLEANING SOLVENT (VARSOL/WHITE SPIRIT)
(Ref. 20-31-00)
C. Expendable Parts
-------------------------------------------------------------------------------FIG.ITEM |DESIGNATION |IPC-CSN -------------------------------------------------------------------------------
2 seals 32-49-16 01 -050 5 cotter pin 32-49-16 01 -010 12 cotter pins 32-11-13 01A-200 12 cotter pins 32-11-13 01E-200
D. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-002 Jacking for Main Gear Wheel Change 12-14-32-614-001 Nitrogen Filling of the Tires 29-10-00-863-002 Pressurize the Yellow Hydraulic System 32-41-00-210-003 Inspection/Check of the Pressure of Tires 32-41-00-910-001 Tire Mixability Precautions 32-42-27-000-001 Removal of the Brake (2641GM,2642GM,2643GM,2644GM) 32-42-27-400-001 Installation of the Brake
(2641GM,2642GM,2643GM,2644GM) 32-48-00-720-001 Functional Test of the Brake Fans 32-49-00-720-001 Crosscheck TPIS Reading and Tire Pressure Gauge 32-41-11-991-012 Fig. 401
3. Job Set-up
__________
Subtask 32-41-11-941-081
A. Safety Precautions
(1)
Make sure that the safety barriers are in position.
(2)
Make sure that the warning notice is in position in the cockpit to tell persons not to operate the landing gear.
1EFF : 051-099, 1 32-41-11Page 407 1 1 Config-3 May 01/05 1 1 1CES 1
(3) Make sure that the wheel chocks are in position. Subtask 32-41-11-865-093
B. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRK FAN/WHEELS/3 AND 4 2GS L35 121VU HYDRAULIC/BRK FAN/WHEELS/1 AND 2 1GS L32 121VU HYDRAULIC/BRK/FAN/CTL 3GS M32 121VU HYDRAULIC/TIRE/PRESS 1GV M31
Subtask 32-41-11-860-092
C. Aircraft Maintenance Configuration
(1)
Make sure that the PARK BRK control switch is set to ON. NOTE : On the panel 400VU, make sure that brake pressure indication
____ on the Yellow brake-pressure triple indicator is correct. If necessary pressurize the brake accumulator with Yellow pump (Ref. TASK 29-10-00-863-002).
(2)
Make sure that the related axle is lifted with a jack (Ref. TASK 07-12-00-582-002).
4. Procedure
_________ (Ref. Fig. 401/TASK 32-41-11-991-012) NOTE : If the wheel is equipped with a pressure sensor seal cap, make sure
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(74)
