(5)
Tighten the nuts (1).
(6)
Install a new tab lock washer (18) on the shaft assembly (3). NOTE : Make sure that the inner tab of the lockwasher is correctly
____
engaged in the shaft groove.
1EFF : ALL 1 32-33-14Page 420 1 1 Feb 01/04 1 1 1CES 1
(7)
Install the nut (17).
(8)
TORQUE the nut (17) to 3 m.daN (22.12 lbf.ft).
(9)
Safety the nut (17) with an outer tab of the lockwasher (18).
(10)
Put and hold the bellcrank (14) on the shaft assembly (3).
(11)
Install the tapered bolt (15), the bush (7), the washer (8) and the nut (9).
(12)
Tighten the nut (9) and safety it with a new cotter pin (10) (10).
(13) Install the rods (4) and (5) on the bellcrank (14) with the bolts R (16), the bushes (6), the washers (13) and the nuts (11).
(14)
Tighten the nuts (11) and safety them with new cotter pins (12) (12). Subtask 32-33-14-820-051
B. Rod Adjustement
(1)
Adjust the adjustable rods (4) and (5) (Ref. TASK 32-33-00-820-002). Subtask 32-33-14-914-051
C. Protection
(1) Apply SPECIAL MATERIALS STORAGE PRESERVATION (Material No. 15-008) to:
-
the nut (9), the washer (8) and the bush (7)
-
the nuts (11), the washers (13)
-
the heads of the bolts (16)
-the nut (17) and the lock washer (18).
Subtask 32-33-14-942-052
D. Installation of NLG Free-Fall Extension Cables.
(1)
Install the NLG free-fall extension cables (Ref. TASK 32-33-16-400-001).
(2)
Adjust the tension of the cables (Ref. TASK 32-33-00-820-001).
1EFF : ALL 1 32-33-14Page 421 1 1 Feb 01/04 1 1 1CES 1 Subtask 32-33-14-720-051
E. Test CAUTION : MAKE SURE THAT THE RIGGING PINS ARE REMOVED BEFORE OPERATION OF
_______ THE FREE FALL SYSTEM. DAMAGE WILL OCCUR IF THE RIGGING PINS ARE INSTALLED DURING SYSTEM OPERATION.
R (1) Do a functional test of the Nose landing-gear free-fall extension R system (Ref. TASK 32-33-00-720-004).
5. Close-up
________
Subtask 32-33-14-862-051
A. De-energize the ground service network
(Ref. TASK 24-42-00-862-001).
Subtask 32-33-14-410-051
B. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the floor panels 211FF, 211JF (Ref. TASK 53-12-11-400-001).
(3)
Remove the warning notice(s).
(4)
Remove the access platform(s).
(5)
Close the NLG doors (Ref. TASK 32-22-00-410-001).
1EFF : ALL 1 32-33-14Page 422 1 1 Aug 01/04 1 1 1CES 1 GEARBOX - REDUCTION - REMOVAL/INSTALLATION
__________________________________________
TASK 32-33-15-000-001
Removal of the Reduction Gearbox
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific shim(s)
No specific warning notice(s)
No specific access platform 1.7 m (5 ft. 7 in.)
98A27801001000 1 RIGGING PIN
98A27901002000 1 PIN, RIGGING - RUDDER CONTROL
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
32-00-00-481-001 Installation of the Safety Devices on the Landing
Gears 32-22-00-010-001 Nose Gear Doors - Ground Doors Opening 53-12-11-000-001 Removal of the Cockpit Floor Panels from FR1 Thru
FR12 32-33-15-991-002 Fig. 401 32-33-15-991-001 Fig. 402
1EFF : ALL 1 32-33-15Page 401 1 1 Feb 01/98 1 1 1CES 1
3. Job Set-up
__________ Subtask 32-33-15-941-050
A. Safety Precautions
(1)
In the cockpit, on the panel 400VU put warning notice(s) in position to tell persons not to operate the landing gear control lever.
(2)
Make sure that the ground safety locks are on the landing gear (Ref. TASK 32-00-00-481-001).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架6(16)
