S 024-024-C00
(6) Remove the core sensor.
(a)
Remove 2 bolts and 2 nuts that attach the core sensor to the bracket at the top of the engine.
(b)
Remove the core sensor from the engine.
TASK 77-31-02-404-036-C00
3. Core Sensor Installation
________________________
A. References
(1)
AMM 71-11-02/201, Fan Cowl Panels
(2)
AMM 77-31-00/501, AVM System
(3)
AMM 78-31-00/201, Thrust Reverser System
B. Access
(1) Location Zone
504 Left Engine - Turbine Rear Frame
604 Right Engine - Turbine Rear Frame
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-31-02
ALL ú ú C01 Page 402 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
SEE A
SEE B
CORE
VIBRATION
SENSOR
CABLE
CONNECTOR
CABLE
CLAMP (1)
CORE VIBRATION SENSOR CONNECTOR ON THE CORE VIBRATION SENSOR
A B
Installation of the Core Vibration Sensor
Figure 401
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-31-02
ALL ú ú C01 Page 403 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
(2) Access Panel
5738L Thrust Reverser - Left Engine
5739L Thrust Reverser - Left Engine
5838R Thrust Reverser - Right Engine
5839R Thrust Reverser - Right Engine
C. Procedure
S 424-025-C00
(1) Install the core sensor (Fig. 401).
(a)
Apply a thin layer of grease to the threads of the 2 screws and the 2 bolts.
(b)
Attach the core sensor on the turbine rear flange with 2 bolts and 2 nuts.
(c)
Tighten the bolts to 100-110 pound-inches (11.5-12.5 N.m.).
S 434-026-C00
(2) Connect the core sensor cable.
(a) Attach the cable to the clamps with a bolt and a nut, at these locations: 1) At 3 clamps on flange T on the turbine section. 2) At a clamp on the support bracket, attached to flange T on
the turbine section.
3) At 3 clamps on flange S on the turbine section.
4) At 3 clamps between flange S on the turbine section and the
electrical connector.
5) ENGINES POST-CFMI-SB 77-001; (ENGINES WITH A CLAMP ON THE INSTRUMENTATION BOSS); At a clamp on an instrumentation boss at the 10 o'clock position on flange T.
(b)
ENGINES POST-CFMI-SB 77-001; (ENGINES WITH A CLAMP ON THE INSTRUMENTATION BOSS); Tighten the bolt on that clamp to 100-110 pound-inches (11.5-12.5 N.m).
(c)
Tighten the bolts on the clamps to 53-62 pound-inches (6-7 N.m). 1) Tighten the bolts in a sequence from the clamp near the
core sensor to the clamp near the electrical connector.
(d)
Attach the cable to the clamp, near the electrical connector, with a bolt and a nut.
(e)
Tighten the bolt on the clamp to 100-110 pound-inches (11.5-12.5 N.m).
(f)
Attach the electrical connector with 2 plates and 4 screws. 1) Tighten the screws. 2) On the screws with the lockwire or the safety cable,
install the lockwire or the safety cable on the screws.
3) On the screws without the lockwire or the safety cable, apply a thin layer of Loctite 241 (CP2246) on the threads of the screws.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-31-02
ALL ú ú C01 Page 404 ú Mar 12/01
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机指示 ENGINE INDICATIN(93)
