(2)
Access Panel
5746L Left Fan Cowl Panel . Left Engine
5846R Left Fan Cowl Panel . Right Engine
E. Prepare to do the System Test (Fig. 502)
S 865-058-C00
(1) AIRPLANES WITHOUT EIS;
For the applicable engine, open these circuit breakers:
(a) P6 Main Power Distribution Panel
1) C00734 TACH IND ENG 1 N2
2) C00735 TACH IND ENG 2 N2
S 865-059-C00
(2) AIRPLANES WITH EIS;
For the applicable engine, open these circuit breakers:
(a) P6 Main Power Distribution Panel
1) C01182 EIS PRIMARY 1 (Engine 1)
2) C01184 EIS PRIMARY 2 (Engine 1)
3) C01183 EIS PRIMARY 3 (Engine 2)
4) C01185 EIS PRIMARY 4 (Engine 2)
S 015-056-C00
(3)
Open the left fan cowl panel (AMM 71-11-02/201).
S 485-067-C00
(4)
Connect the test equipment.
(a)
Disconnect the electrical connector D552 from the N2 speed sensor.
(b)
Connect the applicable cable from the test box to the receptacle from the N2 speed sensor.
(c)
Connect the function generator to the mating receptacle on the test box.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-12-00
ALL ú ú C04 Page 508 ú Mar 15/99
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
Test of the N2 Speed Sensor (Control Alternator)
Figure 502
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-12-00
ALL ú ú C01 Page 509 ú Jul 12/01
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 865-066-C00
(5) AIRPLANES WITHOUT EIS;
For the applicable engine, close these circuit breakers:
(a) P6 Main Power Distribution Panel
1) C00734 TACH IND ENG 1 N2
2) C00735 TACH IND ENG 2 N2
S 865-068-C00
(6) AIRPLANES WITH EIS;
For the applicable engine, close these circuit breakers:
(a) P6 Main Power Distribution Panel
1) C01182 EIS PRIMARY 1 (Engine 1)
2) C01184 EIS PRIMARY 2 (Engine 1)
3) C01183 EIS PRIMARY 3 (Engine 2)
4) C01185 EIS PRIMARY 4 (Engine 2)
S 865-103-C00
(7) Supply electrical power (AMM 24-22-00/201).
F. Do the System Test of the N2 Tachometer System
S 735-068-C00
(1) Do a check of the N2 indicating system at 25% N2.
(a)
Apply a 3.0 |0.5v ac signal, at 467.5 Hz, with the function generator. 1) Connect a multimeter to the DVM terminals on the test box
to make sure the signal is the correct voltage.
(b)
Make sure the N2 display shows 25 |0.1% N2 and the pointer is at 25 |0.5% N2.
S 735-069-C00
(2) Do a check of the over-limit light.
(a)
Increase the frequency on the function generator until the red warning light, that shows an over-limit condition, comes on.
(b)
Make sure the indicator shows 105.1 |0.1% N2 when the red warning light comes on.
(c)
Decrease the frequency on the function generator until the red warning light, that shows an over-limit condition, goes off.
(d)
Make sure the indicator shows 0.5 |0.1% N2 less than when the red warning light came on.
S 735-070-C00
(3) Do a check of the N2 indicating system with no input.
(a)
Disconnect the function generator from the test box.
(b)
Make sure the display does not show and the pointer moves to zero.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机指示 ENGINE INDICATIN(9)
