B. References
(1)
AMM 71-00-00/501, Power Plant
(2)
AMM 71-11-02/201, Fan Cowl Panels
(3)
AMM 77-12-00/501, Engine Tachometer System
C. Access
(1)
Location Zone
503 Left Engine - Fan Frame 4 o'clock
603 Right Engine - Fan Frame 4 o'clock
(2)
Access Panel
5737L Right Fan Cowl Panel - Left Engine
5837R Right Fan Cowl Panel - Right Engine
D. Procedure
S 162-029-C00
(1) Do these steps to prepare for the installation:
(a)
Apply a layer of petrolatum on a new O-ring.
(b)
Fully clean the probe pole pieces on the N1 speed sensor with a clean, dry cloth.
(c)
Remove the magnetic particles with a piece of adhesive tape.
(d)
Remove the protective cap from the electrical connector.
S 422-030-C00
(2) Do these steps to install the N1 speed sensor (Fig. 201):
(a)
Install the O-ring on the guide tube.
(b)
Carefully install the N1 speed sensor on the fan frame.
NOTE: The N1 speed sensor has a spring to keep it in its
____
position.
S 222-017-C00
(3) Make sure the N1 speed sensor has the correct clearance.
(a) Measure the clearance between the probe flange of the N1 speed sensor and the fan frame sleeve.
CAUTION: MAKE SURE YOU INSTALL THE N1 SPEED SENSOR WITH THE CORRECT
_______ CLEARANCE. IF THE CLEARANCE IS NOT CORRECT, YOU CAN CAUSE DAMAGE TO THE N1 SENSOR.
(b)
If the clearance is not 0.118-0.236 inch (3.0-6.0 mm), remove the N1 speed sensor and look for damage (distortion, incorrect orientation of sensor).
(c)
If you cannot install the N1 speed sensor with the correct clearance, replace the N1 speed sensor.
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-12-01
ALL ú ú C01 Page 204 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
S 432-018-C00
(4) Install the bolts in the sensor:
(a) Apply a thin layer of antiseize compound to the bolts.
(b) Install the two bolts in the sensor.
1) Tighten the bolts to 100-110 pound-inches (11-12 N.m).
2) Tighten one bolt and then the other, in increments, to make
sure you do not bend the N1 speed sensor.
S 432-019-C00
(5) Connect the electrical cable to the N1 speed sensor:
(a) Attach the electrical connector and turn the knurled coupling
ring while you move the backshell assembly back and forward.
(b) Tighten the electrical connector with your hand.
(c) Then, tighten the electrical connector with connector pliers
that have padded jaws.
(d) Make sure the electrical connector is correctly installed; it
must not move.
S 412-022-C00
(6) Close the fan cowl panel (AMM 71-11-02/201).
S 712-020-C00
(7) Do this task "Operational Test of the N1 Tachometer System"
(AMM 77-12-00/501).
(a) Do the leak check for engine operation at 70% N1 as shown in
the Test Reference Table (AMM 71-00-00/501).
EFFECTIVITYùùùùùùùùùùùùùùùùùùùùùùùùùùùùùù. ú
77-12-01
ALL ú ú C01 Page 205 ú Nov 15/95
BOEING PROPRIETARY - Copyright (C) - Unpublished Work - See title page for details.
////////////////////////A / /
CFM56 ENGINES
737-300/400/500/ /MAINTENANCE MANUAL ////////////////////////
N1 AND N2 TACHOMETER INDICATORS - REMOVAL/INSTALLATION
______________________________________________________
1. General
_______
A. This procedure contains four tasks:
(1)
Remove the N1 indicator
(2)
Install the N1 indicator
(3)
Remove the N2 indicator
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：737-300 400 500 AMM 飞机维护手册 发动机指示 ENGINE INDICATIN(12)
