-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
Subtask 57-53-00-110-052
A. Preparation for Inspection
(1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the inspection area.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 608 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Outboard Flap Inboard Rib
Figure 602/TASK 57-53-00-991-004
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 609 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 Subtask 57-53-00-210-052
B. Inspection
(1) Examine the external surface of the outboard flap at the inboard-rib forward-section. Make sure that:
-
there is no corrosion
-
there are no cracks
-
there are no scores or damage to the roller
-
there is not too much play of the roller.
(Ref. Fig. 602/TASK 57-53-00-991-004)
NOTE : If the AXIAL PLAY "X" or the RADIAL PLAY "Y" is more than 0.25
____ mm (0.0098 in.), do a check of the liner for damage and wear.
(2) Examine, as far as possible, the internal surface of the outboard flap at the inboard-rib forward section and the roller. Make sure that:
-
there is no corrosion
-
there are no cracks
-
there are no dents or other damage.
NOTE : If necessary, refer to the ASRM (Ref. ASRM 575300) for the
____
correct repair procedure.
5. Close-up
________
Subtask 57-53-00-410-051
A. Close Access
(1)
Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the correct dimensions, to make the inspection covers.
(2)
Install the inspection covers.
(3)
Install the flap kink seals (Ref. TASK 27-54-61-400-006).
Subtask 57-53-00-865-056
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 6CV, 8CV.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 610 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
Subtask 57-53-00-860-083
C. Aircraft Maintenance Configuration
(1) Make sure that the work area is clean and clear of tool(s) and other items.
(2) Fully retract the flaps (Ref. TASK 27-50-00-866-009). Subtask 57-53-00-942-052
D. Removal of Equipment
(1)
Remove the access platform(s).
(2)
Remove the warning notice(s).
(3)
Remove the safety barriers.
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 57-53-00Page 611 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1
TASK 57-53-00-220-002
Special Detailed Inspection of the Outboard Flap, Inboard Rib, Forward Section Including Roller, Internal and External, LH/RH
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Refer to the MPD TASK: 575307-02
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼4(70)
