(b)
Remove the seal (3) from the panel (6).
(c)
Remove the support channel (5) from inside the seal (3).
(d)
Discard the seal (3).
(2) Make sure that the parts retained from the removed component are clean and in the correct condition.
R (3) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING R AGENTS (Material No. 11-026) to clean the component interface and/or R the adjacent area.
(4) Get a new seal for the applicable panel:
FOR 573AB
seal (3)
FOR 673AB
seal (3)
FOR 573BB
seal (3)
FOR 673BB
seal (3)
FOR 573CB
seal (3)
FOR 673CB
seal (3)
FOR 573FB
seal (3)
FOR 673FB
seal (3)
FOR 575AB
seal (3)
FOR 675AB
R Lower Trailing Edge Panel Seals Inboard of Rib 22 - Typical Installation Figure 404/TASK 57-51-37-991-001
1EFF : ALL 1 57-51-37Page 438 1 1 May 01/05 1 1 1CES 1
seal (3)
FOR 575BB
seal (3)
FOR 675BB
seal (3)
FOR 575CB
seal (3)
FOR 675CB
seal (3)
FOR 575DB
seal (3)
FOR 675DB
seal (3)
FOR 575EB
seal (3)
FOR 675EB
seal (3)
FOR 575FB
seal (3)
FOR 675FB
seal (3)
FOR 575GB
seal (3)
FOR 675GB
seal (3)
FOR 575HB
seal (3)
FOR 675HB
seal (3).
(5)
Put the support channel (5) in position inside the new seal (3). Make sure that the holes in the support channel (5) are in-line with the smaller attachment holes in the seal (3).
(6)
Apply SEALANTS (Material No. 09-001) to the shank and under the heads of the bolts (4).
(7)
Install the bolts (4) through the larger access holes in the seal (3) and through the support channel (5), the attachment holes in the seal
(3) and the panel (6).
(8)
Install the washers (2) and the nuts (1).
1EFF : ALL 1 57-51-37Page 439 1 1 May 01/05R 1 1 1CES 1
(9) TORQUE the nuts (1) to between 0.34 and 0.40 m.daN (30.08 and 35.39 lbf.in).
NOTE : To prevent distortion of the seal (3), do not tighten the nuts
____
(1) more than the specified torque value.
Subtask 57-51-37-960-052
R B. Replacement of the Seal on the Access Panels Outboard of STA11664/RIB 22 (Ref. Fig. 405/TASK 57-51-37-991-002)
R (1) To remove the seal (19), do the steps that follow:
(a)
Remove the bolts (17).
(b)
Remove the support channel (16) from the seal (19) and remove the seal from the access panel (18).
(c)
Discard the seal (19).
(2)
Make sure that the parts retained from the removed components are clean and in the correct condition.
(3)
Use MISCELLANEOUS (Material No. 19-003), made moist with CLEANING AGENTS (Material No. 11-026) to clean the component interface and/or the adjacent area.
(4)
Get a new seal for the applicable panel:
FOR 575KB
seal (19)
FOR 675KB
seal (19)
FOR 575LB
seal (19)
FOR 675LB
seal (19)
FOR 575MB
seal (19)
FOR 675MB
seal (19).
(5)
Apply SEALANTS (Material No. 09-001) to the shank and under the heads of the bolts (17).
(6)
Put the new seal (19) and the support channel (16) in position on the access panel.
R Lower Trailing Edge Panel Seals Outboard of Rib 22 - Typical Installation Figure 405/TASK 57-51-37-991-002
1EFF : ALL 1 57-51-37Page 441 1 1 May 01/05 1 1 1CES 1
R R (7) Install the bolts (17) through the access panel (18) and the seal (19) into the anchor nuts on the support channel (16). Do not tighten the bolts (17).
R R R (8) Make sure that the width of the seal (19) (dimension X) is 18 mm (0.7086 in.) + 0.0 mm (0.0000 in.) - 2.0 mm (0.0787 in.) along the length of the access panel (18).
R (9) TORQUE tighten the bolts (17) to between 0.11 and 0.13 m.daN (9.73 and 11.50 lbf.in).
NOTE : To prevent distortion of the seal (19), do not tighten the____ bolts (17) more than the specified torque value.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼4(4)
