R Subtask 57-52-00-865-113
R C. Open, safety and tag this(these) circuit breaker(s):
R -------------------------------------------------------------------------------
R PANEL DESIGNATION IDENT. LOCATION
R -------------------------------------------------------------------------------
R 49VU FLIGHT CONTROLS/FLP/CTL AND MONG/SYS1 6CV B07
R 121VU FLIGHT CONTROLS/FLP/CTL AND/MONG/SYS2 8CV Q21
R Subtask 57-52-00-010-087
R D. Get Access
R (1) Put the adjustable access platform in position at the applicable zone
R 500(600).
R 4. Procedure_________
R (Ref. Fig. 630/TASK 57-52-00-991-034)
R Subtask 57-52-00-100-051
R A. Preparation for Inspection
R (1) Use a MISCELLANEOUS (Material No. 19-003), made moist with CLEANING
R AGENTS (Material No. 11-026) to clean the applicable area for
R inspection.
R Subtask 57-52-00-210-067
R B. Inspection
R (1) Do an inspection of the upper and lower skin external surface of the
R inboard double-slotted flap, LH/RH. Make sure that:
R - there is no damage
R - there are no cracks
R - there is no corrosion
R - the paint finish is in the correct condition.
R NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____
R correct repair procedure.
R Inboard Double-Slotted Flap - Inspection Area R Figure 630/TASK 57-52-00-991-034
1EFF : 301-399, 1 57-52-00Page A682 1 1 May 01/04 1 1 1CES 1
R 5. Close-up
________
R Subtask 57-52-00-865-114
R A. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s):
R 6CV, 8CV.
R Subtask 57-52-00-860-108
R B. Aircraft Maintenance Configuration
R (1) Fully retract the flaps (Ref. TASK 27-50-00-866-009).
R Subtask 57-52-00-942-082
R C. Removal of Equipment
R (1) Remove the access platform(s).
R (2) Remove the safety barriers.
R (3) Remove the warning notice(s).
R (4) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
**ON A/C ALL
TASK 57-52-00-200-011
Inspection of Inboard Flap, Bottom Surface, Drain Holes and Inspection Holes
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:
_______
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
-
DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
-MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY. INCORRECT INSTALLATION CAN CAUSE DAMAGE.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notices
R No specific 5.0mm (0.2 in.) dia. non-metallic probe No specific access platform 2.5 m (8 ft. 2 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼4(59)
