R 1EFF : 301-399, 1 57-52-00Page 697 1 1 May 01/04 1 1 1CES 1R Inboard Flap - Inboard Trunnion - Inspection Area R Figure 616/TASK 57-52-00-991-016
R 1EFF : 301-399, 1 57-52-00Page 698 1 1 May 01/04 1 1 1CES 1
R Subtask 57-52-00-280-057
R B. Inspection
R (1) Do a special detailed inspection of the trunnion attachment bracket
R and inboard trunnion LH/RH (Ref. NTM 57-52-23 PART 9).
R NOTE : If necessary, refer to the ASRM (Ref. ASRM 575200) for the____
R correct repair procedure. If the defect is not included in
R this repair, you must request a procedure from Airbus
R Industrie.
R 5. Close-up________
R Subtask 57-52-00-410-069
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Use BONDING AND ADHESIVE COMPOUNDS (Material No. 08-061A) cut to the
R correct dimensions, to make the new covers for the inspection holes.
R (3) Install the new covers on the inspection holes in the lower surface
R of the flap.
R (4) Install the access panel 581AT (681AT) in the upper surface of the
R flap.
R Subtask 57-52-00-865-088
R B. Remove the safety clip(s) and the tag(s) and close this(these) circuit
R breaker(s) 6CV, 8CV.
R Subtask 57-52-00-860-054
R C. Aircraft Maintenance Configuration
R (1) Remove the LOCKING TOOL - FLAP/SLAT CONTROL LEVER from the flap/slat
R control lever.
R (2) Retract the flaps (Ref. TASK 27-50-00-866-009).
R Subtask 57-52-00-942-068
R D. Removal of Equipment
R (1) Remove the access platform(s).
R (2) Remove the safety barriers.
R (3) Remove the warning notice(s).
R (4) Remove the ground support and maintenance equipment, the special and
R standard tools and all other items.
R TASK 57-52-00-210-002
R Detailed Visual Inspection of Inboard Double Slotted Flap, Drive Strut for Flap
R and Drive Lever for Flap Track Fairing, Including Attachment Brackets ....
R WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU_______
R START A TASK ON OR NEAR:
R - THE FLIGHT CONTROLS
R - THE FLIGHT CONTROL SURFACES
R - THE LANDING GEAR AND THE RELATED DOORS
R - COMPONENTS THAT MOVE.
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R CAUTION : BE CAREFUL WHEN YOU DO MAINTENANCE TASKS ON THE WING TRAILING EDGE:_______
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE RACEWAYS.
R - DO NOT CAUSE DAMAGE TO THE ELECTRICAL CABLE INSTALLATIONS.
R - MAKE SURE THAT THE ELECTRICAL CABLES ARE INSTALLED CORRECTLY.
R INCORRECT INSTALLATION CAN CAUSE DAMAGE.
R 1. Reason for the Job__________________
R Refer to the MPD TASK: 575225-01
R Detailed Visual Inspection of Inboard Double Slotted Flap, Drive Strut for
R Flap and Drive Lever for Flap Track Fairing, Including Attachment Bracket to
R the Flap at Track 2, LH/RH
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s)
R No specific safety barriers
R No specific spark-proof
R No specific warning notice
R No specific access platform 2.5 m (8 ft. 2 in.)
R B. Referenced Information
R -------------------------------------------------------------------------------R REFERENCE DESIGNATION R -------------------------------------------------------------------------------
R 27-50-00-866-008 R 27-50-00-866-009 R 57-55-11-000-004 R 57-55-11-400-004 R R ASRM 575200 R 57-52-00-991-017
R 3. Job Set-up
__________
R Subtask 57-52-00-941-070
R A. Safety Precautions Extension of the Flaps on the Ground Retraction of the Flaps on the Ground Removal of the Flap Track Fairings Nos. 2, 3 and 4 Installation of the Flap Track Fairings Nos. 2, 3 and 4 (for corrective action) Fig. 617
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM WINGS 机翼4(37)
