(1) Remove the SHUNT PLUG - FIRE EXTINGUISHER CARTRIDGE (263193) from the
cartridge (9). R **ON A/C 051-099, 106-149, 151-199, 211-299, 301-399, 401-499,
Subtask 26-21-41-420-050-A
A. Installation of the Fire-Extinguisher Bottle
(1)
Remove the blanking plug from the line (4).
(2)
Do an inspection of the component interface and/or the adjacent area.
(3)
Clean the component interface and/or the adjacent area.
(4)
Install the bottle (12): WARNING : BE VERY CAREFUL WHEN YOU MOVE A FILLED FIRE EXTINGUISHER
_______ BOTTLE. A HEAVY SHOCK COULD CAUSE PERCUSSION.
(a) Install the bonding lead (14): 1 Put the fire extinguisher bottle (12) with the discharge
_ head/cartridge assembly installed on it in the pylon.
2 Turn the bottle (12) to install the bonding lead (14), the
_ washer (16) and the nut (15) on the screw (17) on the discharge head (10).
(b) Put the fire extinguisher bottle (12) on its support and push the discharge head (10) into the line (4).
(5)
Tighten the nut (6) on the union (5) by hand as follows:
-while you hold the nut pin outside its housing, tighten the nut (6) until it stops,
-loosen the nut (a quater of a turn maximum) until the pin engages its housing.
(6)
Install the washers (3), the screws (2) and tighten them.
Subtask 26-21-41-081-050-A
R B. Remove the Safety Tool WARNING : THE CARTRIDGE IS AN EXPLOSIVE DEVICE. TO PREVENT EXPLOSION OF
_______ THE CARTRIDGE (NOT FIRED) AND INJURY TO PERSONNEL: -INSTALL THE APPLICABLE PROTECTIVE DEVICE (CAP OR PLUG). THIS WILL PROTECT THE ELECTRICAL CONNECTOR OF THE CARTRIDGE. DO NOT USE A FOIL SHUNT.
R (1) Remove the PROTECTIVE CAP - FIRE EXTINGUISHER CARTRIDGE (861823) from the cartridge (9).
**ON A/C ALL
Subtask 26-21-41-420-058
C. Connect the Electrical Connectors
(1)
Remove the blanking caps from the electrical connectors.
(2)
Make sure that the electrical connectors are clean and in the correct condition.
(3)
Connect the electrical connector (1) to the pressure switch (13).
(4)
Connect the electrical connector (8) to the cartridge (9).
5. Close-up
________
Subtask 26-21-41-865-052
A. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
(1)
FOR 6WE1, 6WE2
1WE1, 2WE1.
(2)
FOR 8WE1, 8WE2
1WE2, 2WE2.
Subtask 26-21-41-710-050
B. Do these Test
(1)
Do an operational test of the loop/squib (Ref. TASK 26-12-00-710-001).
(2)
Do an operational test of the low-pressure indicating circuit (Ref. TASK 26-21-00-710-002).
Subtask 26-21-41-410-050
C. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
FOR 6WE1, 8WE1
-Close the access doors 415BR, 415BL.
(3)
FOR 6WE2, 8WE2
-Close the access doors 425BR, 425BL.
(4)
Remove the access platform(s).
R 1EFF : ALL 1 26-21-41Page 416 1 1 May 01/01 1 1 1CES 1
TASK 26-21-41-000-004
Removal of the Cartridge of the Engine Fire-Extinguisher Bottle WARNING : THE CARTRIDGE IS AN EXPLOSIVE DEVICE. TO PREVENT EXPLOSION OF THE
_______
CARTRIDGE (NOT FIRED) AND INJURY TO PERSONNEL:
-INSTALL THE APPLICABLE PROTECTIVE DEVICE (CAP OR PLUG).
THIS WILL PROTECT THE ELECTRICAL CONNECTOR OF THE CARTRIDGE.
DO NOT USE A FOIL SHUNT.
WARNING : DO NOT REMOVE/INSTALL THE DISCHARGE HEAD WITH THE CARTRIDGE
_______
INSTALLED.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking plug R 263193 1 SHUNT PLUG - FIRE EXTINGUISHER CARTRIDGE
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址:A320飞机维护手册 AMM FIRE PROTECTION 防火2(32)