R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 26-21-00Page 549 1201-228, 301-302, 1May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
B. Push and release the BLEED pushbutton switch.
6. On the MCDU 1(2) (on the center pedestal panel 11VU):
-set the BMC 1(2) CURRENT STATUS page.
- open, safety and tag the circuit breaker 2HA1(2HA2).
-remove the safety clip and the tag, and close the circuit breaker 2HA1(2HA2).
7. On the MCDU 1(2) (on the center pedestal panel 11VU):
-
set the AC Gen page.
-
set the LAST LEG REPORT.
8. On the overhead panel 20VU, on the ENG/APU fire panel 1WD:
-push the ENG 1(2) FIRE
pushbutton switch.
* the VALVE-G(Y) PUMP FIRE ENG 1(2) is shown not in-line and in amber.
-The HYD page goes out of view and theBLEED page comes into view:
* THE PACK-FLOW CONTROL VALVE 1(2) is shown not in-line and in green.
On the MCDU 1(2) (on the centerpedestal panel 11VU), through theCURRENT STATUS:
-make sure that the BIT 19 of the LABEL 67(66) is at 1.
In the zone 414, 424 of the engine pylon:
-Make sure that the voltmeter shows28VDC.
On the MCDU 1(2) (on the centerpedestal panel 11VU):
-On the LAST LEG REPORT page:
* read GND and this message CHECK
FIRE HANDLE 1(2) RESET GEN 1(2).
On the overhead panel 20VU, on theENG/APU fire panel 1WD:
-
the SQUIB legends of the AGENT 1 and2 pushbutton switches go off.
On the upper display unit of the ECAM system:
-
the crosses go out of view and the main parameters of the related engine come into view.
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 26-21-00Page 550 1201-228, 301-302, 1May 01/05 1 1 1CES 1
-------------------------------------------------------------------------------
ACTION RESULT -------------------------------------------------------------------------------
9. On the center pedestal, on the control panel of the ECAM system (11VU):
A. push and release the HYD pushbutton switch.
B. Push and release the FUEL pushbutton switch.
10. On the MCDU 1(2) (on the center pedestal panel 11VU):
-Set the BMC 1(2) CURRENT STATUS page.
11. On the overhead circuit breaker panel 49VU:
-close the circuit breaker 1QG(2QG).
12. On the rear circuit breaker panel 121VU:
On the lower display unit of the ECAM system (4VU):
-
the BLEED page is in view
* the PACK-FLOW CONTROL VALVE 1(2) is shown in-line and in green.
-
the BLEED page goes out of view andthe HYD page comes into view
* the VALVE-G(Y) PUMP FIRE ENG 1(2) is shown in-line and in green.
-The HYD page goes out of view and theFUEL page comes into view:
* the ACTUATOR LP FUEL SHUT OFF VALVE ENG 1(2) is shown in-line and in green.
On the MCDU 1(2) (on the center pedestal panel 11VU):
-On the LAST LEG REPORTS page of the AC Gen:
* the CHECK FIRE HANDLE 1(2) RESET GEN 1(2) message stays in of view and goes out of view for the next flight.
On the MCDU 1(2) (on the centerpedestal panel 11VU):
-Make sure that the BIT 19 of theLABEL 67(66) is at zero.
On the MCDU 1(2) and on the lowerdisplay unit of the ECAM system:
-There is no change (FUEL page)
On the MCDU 1(2) and on the lowerdisplay unit of the ECAM system:
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 26-21-00Page 551 1201-228, 301-302, 1May 01/05 1 1 1CES 1
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FIRE PROTECTION 防火2(20)
