曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
2. The confirmation page will display the location (and other
applicable data) for the reference waypoint. The legend
ACCEPT will appear in the cursor block next to the [5L] line
select key. If there are two or more locations or facilities with the
same identifier, the page title will indicate 1/2, 1/3, etc.,
additional locations can be displayed using the NEXT key.
When the desired location of the reference waypoint is
displayed, press the ACCEPT line select key or the ENTER key.
3. The cursor will move to the RADIAL field. Enter the radial
(degrees and tenths - leading zeroes not required) from the
reference waypoint on which the newly defined waypoint lies.
Press ENTER.
4. The cursor will move to the DISTANCE field. Enter the new
waypoint’s distance from the reference waypoint (nautical miles
and tenths - leading zeros not required). Press ENTER. The
coordinates of the newly defined waypoint will be displayed.
5. The legend ACCEPT WPT will appear in the cursor block next to
the [5L] line select key. Press either the ACCEPTWPT line
select key, or the ENTER key.
Section IV
Data Base
2423sv602 4-77
Change 1
To define a position by the Radial/Radial method:
1. The cursor will appear over the REF WPT field when the Define
Position page is accessed. Enter the name of the first reference
waypoint, navaid or airport from which the new waypoint will be
derived. Press ENTER.
2. The confirmation page will display the location (and other
applicable data) for the reference waypoint. The legend
ACCEPT will appear in the cursor block next the [5L] line select
key. If there are two or more locations or facilities with the same
identifier, the page title will indicate 1/2, 1/3, etc., additional
locations can be displayed using the NEXT key. When the
desired location of the reference waypoint is displayed, press
the ACCEPT line select key or the ENTER key.
3. The cursor will move to the RADIAL field. Enter the radial
(degrees and tenths - leading zeroes not required) from the
reference waypoint on which the newly defined waypoint lies.
Press ENTER.
4. The cursor will move to the DISTANCE field. Do not make an
entry in the distance field if you desire a Radial/Radial waypoint
definition. Rather, press the [4L] line select key over the WPT
field to identify the second reference waypoint. Enter the name
or identifier of the second reference waypoint. Press ENTER.
5. The confirmation page will again appear displaying the location
for the second reference waypoint. The legend ACCEPT will
appear in the cursor block next to the [5L] line select key. Press
ACCEPT or the ENTER key.
6. The cursor will move to the RADIAL field. Enter the radial
(degrees and tenths - leading zeroes not required) from the
second reference waypoint on which the newly defined waypoint
lies. Press ENTER. The coordinates of the newly defined
waypoint will be displayed.
7. The legend ACCEPT WPT will appear in the cursor block next to
the [5L] line select key. Press either the ACCEPT WPT line
select key, or the ENTER key.
Section IV
Data Base
4-78 2423sv602
Change 1
To define a waypoint by the GPS Position or FMS Position method:
1. Press the [2R] line select key to highlight the latitude field. The
GPS POS and FMS POS legends adjacent to the [3R] and [4R]
line select keys will illuminate in large orange font, indicating that
these options have become available.
2. Press GPS POS or FMS POS as desired.
NOTE: The GPS POS option is only available when the GPS
sensor is in NAV mode and supplying valid data. FMS
position will be available any time the FMS has valid
position data, regardless of the source.
Section IV
Data Base
2423sv602 4-79
Change 1
POSITION MENU Page
The POSITION MENU page is accessed from the DEFINE
POSITION page by pressing the MENU key. This page allows the
operator to define waypoints to 1/10th or 1/100th of a minute
resolution. This feature allows position resolution to approximately
60 minutes and an accuracy of ± 30 feet, and is useful for defining
precise runway touchdown points.
LAT/LON ENTRY- Pressing this line select key will allow selection of
either tenths or hundredths of a minute resolution on the DEFINE
POSITION page.
Section IV
Data Base
4-80 2423sv602
Change 1
Pilot Waypoint Identification Page
This page is accessed by pressing DATA, the PILOT DATA line
select key and the WAYPOINT line select key. This page displays
the waypoint coordinates and provides the means to modify or
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
庞巴迪挑战者手册10(57)
