R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 586 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
4. Procedure
_________
(Ref. Fig. 507/TASK 32-51-00-991-007, 508/TASK 32-51-00-991-008) Subtask 32-51-00-220-056
A. Check and record the secondary voltage at the sensor 3GC
NOTE : The voltages U1 and U2 are in volts (3V approximately).
____
(1)
On panel 402VU, put the A/SKID & N/W STRG switch in OFF position.
(2)
Disconnect the connector (4) from the RVDT 3GC (1).
(3)
Connect the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (F26792000-1) (3) between the connector (4) and the RVDT 3GC (1).
(4)
Connect an AC voltmeter (minimum range: 0-20V, accuracy: 1 mV, frequency: 50-2000 Hz) to the SECONDARY VOLTAGE connections on the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (3).
(5)
Open the CBs of the BSCU SYS2 (3GG and 4GG).
(6)
Make sure that the CBs of the BSCU SYS1 (1GG and 2GG) are closed.
(7)
On panel 402VU, put the A/SKID & N/W STRG switch in ON position.
(8)
With the captains handwheel, move the steering 75 degrees to the left then 75 degrees to the right then to the zero position.
(9)
Stage 1:
(a)
Make sure that the nose wheel steering handwheels and the rudder pedals are in neutral position. Do not operate them.
(b)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(3) set the selector switch to U1.
(c)
Record the voltage (U1)(in AC voltage).
(d)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(3) set the selector switch to U2.
(e)
Record the voltage (U2)(in AC voltage).
(f)
Calculate the algebraic value x:
x = (U1 - U2)
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 587 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Adjustment of the NWS Position - Sensor Box P/N E21336000
Figure 507/TASK 32-51-00-991-007
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 588 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
NWS Zero Position - Calculated Chart
Figure 508/TASK 32-51-00-991-008
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 589 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(10)
Get the rudder trim calculated value X obtained during Trouble Shooting procedure (Ref. TSM 32-51-00-810-823). On the panel 110VU, set the rudder trim switch to the same value.
(11)
Stage 2:
(a)
Make sure that the nose wheel steering handwheels and the rudder pedals are in neutral position. Do not operate them.
(b)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(3) set the selector switch to U1.
(c)
Record the voltage (U1)(in AC voltage).
(d)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(3) set the selector switch to U2.
(e)
Record the voltage (U2)(in AC voltage).
(f)
Calculate the algebraic value y: y = (U1 - U2)
(12)
Stage 3:
(a) Calculate the algebraic value A: A = (y - x)
NOTE : This voltage value correspond to the trim angle X
____
(13)
On the panel 110VU, set the rudder trim at 0.
(14)
On panel 402VU, put the A/SKID & N/W STRG switch in OFF position.
(15)
Remove the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(3) from the sensor 3GC. R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399,
Subtask 32-51-00-864-058
B. Depressurize the Green hydraulic system (Ref. TASK 29-10-00-864-001).
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 590 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R **ON A/C 401-499,
R Subtask 32-51-00-864-058-A
R B. Depressurize the Yellow hydraulic system (Ref. TASK 29-10-00-864-002).
R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(8)
