-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R R 29-10-00-863-002 29-10-00-864-001 29-10-00-864-002 32-46-00-740-001 TSM 32-51-00-810-823 32-51-00-991-006 32-51-00-991-007 32-51-00-991-008 Pressurize the Yellow Hydraulic SystemDepressurize the Green Hydraulic System Depressurize the Yellow Hydraulic SystemBITE Test of the BSCUFig. 501Fig. 507Fig. 508
3. Job Set-up__________
Subtask 32-51-00-941-056
A. General
R (1) Put a warning placard in the cockpit to tell persons not to operate the landing gear or the N/WS.
(2) On the panel 400VU, make sure that the L/G normal control lever is in the DOWN position.
(3) On the nose gear leg, on the nose wheel steering deactivation electrical box, make sure that the towing lever is in the normal position (engaged position).
(4) Make sure that the N/WS handwheels and the rudder pedals are in the neutral position.
R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399,
Subtask 32-51-00-860-070
B. Aircraft Maintenance Configuration
(1) Lift the aircraft and compress the NLG shock absorber
(a) Lift the front of the aircraft until the nosewheels are clear of the ground (Ref. TASK 07-11-00-581-003).
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 584 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(b) Compress the NLG shock absorber with a nosewheel jack until the dimension H is less than 350 mm (14.0 in.) (Ref. TASK 07-12-00-582-001). (Ref. Fig. 501/TASK 32-51-00-991-006)
(c) Make sure that there is a sufficient clearance between the jack and the nosewheels for the nosewheel steering to operate.
(d) Make sure that you cannot see more than 350 mm (14.0 in.) of the NLG shock absorber dimension H.
NOTE : As an alternative solution, if only jack is not available____ you can use need two 1.2m (4ft.) square steel plates, for this do as follows: - Position a steel plate in front of the nosewheels. - Apply a thick layer of COMMON GREASE (Material No. 04-004) to the upper surface of the steel plate. - Put the other steel plate on the top of the greased steel plate. - Move the aircraft and position the nosewheels on the greased steel plates (Ref. TASK 09-10-00-584-002).
(2) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
(3) Pressurize the Green hydraulic system (Ref. TASK 29-10-00-863-001).
R **ON A/C 401-499,
R Subtask 32-51-00-860-070-A
R B. Aircraft Maintenance Configuration
R (1) Lift the aircraft and compress the NLG shock absorber
R R (a) Lift the front of the aircraft until the nosewheels are clear of the ground (Ref. TASK 07-11-00-581-003).
R R R R (b) Compress the NLG shock absorber with a nosewheel jack until the dimension H is less than 350 mm (14.0 in.) (Ref. TASK 07-12-00-582-001). (Ref. Fig. 501/TASK 32-51-00-991-006)
R R (c) Make sure that there is a sufficient clearance between the jack and the nosewheels for the nosewheel steering to operate.
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page 585 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
R R (d) Make sure that you cannot see more than 350 mm (14.0 in.) of the NLG shock absorber dimension H.
R R R R R R R R R R NOTE : As an alternative solution, if only jack is not available____ you can use need two 1.2m (4ft.) square steel plates, for this do as follows: - Position a steel plate in front of the nosewheels. - Apply a thick layer of COMMON GREASE (Material No. 04-004) to the upper surface of the steel plate. - Put the other steel plate on the top of the greased steel plate. - Move the aircraft and position the nosewheels on the greased steel plates (Ref. TASK 09-10-00-584-002).
R R (2) Energize the aircraft electrical circuits (Ref. TASK 24-41-00-861-002).
R R (3) Pressurize the Yellow hydraulic system (Ref. TASK 29-10-00-863-002).
R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
Subtask 32-51-00-865-092
C. Table of the circuit breakers used in this procedure:
-------------------------------------------------------------------------------
PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 4GG 3GG 1GG 2GG M36M35M34M33
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(7)
