1EFF : ALL 1 32-51-43Page 407 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-51-43Page 408 1 1 Aug 01/05 1 1 1CES 1
R R R (2) Make sure that the reservoir of the Yellow hydraulic system is depressurized. (Ref. TASK 29-14-00-614-001).
R R R R R (3) Make sure that the warning notice(s) is (are) in position to tell persons not to pressurize the Yellow hydraulic system: - on the panel 40VU in the cockpit, - on the ground service panel of the Yellow hydraulic system, access door 196BB.
R R (4) In the cockpit, on the center pedestal, make sure that the free-fall extension handle of the landing gear is in the normal position.
R R R (5) In the cockpit, on the panel 400VU, make sure that the warning notice(s) is (are) in position to tell persons not to operate the landing gear control lever.
R (6) Make sure that the container is in position below the cylinder.
R (7) Make sure that the safety barriers are in position.
R **ON A/C ALL
4. Procedure_________
(Ref. Fig. 401/TASK 32-51-43-991-001)
Subtask 32-51-43-560-050
A. Preparation for Installation
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
NOTE : Lubricate the seals with hydraulic fluid.____
(2) Put the new seals (6), ring (5) and ring (7) on the valve (8).
Subtask 32-51-43-420-050
B. Installation of the Anti Shimmy Valve
(1) Put the valve (8) in the internal diameters of the cylinder (1).
(2) Install the new lock washer (2).
(3)
Install the nut (3) and TORQUE it to between 0.25 and 0.3 m.daN
(22.12 and 26.54 lbf.in).
(4)
Bend over the lock washer (2) to lock the nut (3).
(5)
Remove the blanking plugs from the line end.
(6)
Connect the hydraulic coupling (4).
(7)
TORQUE the hydraulic coupling (4) to between 2.42 and 3.16 m.daN
(17.84 and 23.30 lbf.ft). Subtask 32-51-43-720-050
C. Functional Test
(1) Do a functional test of the nose wheel steering with the handwheel (Ref. TASK 32-51-00-720-003).
5. Close-up
________ Subtask 32-51-43-942-050
A. Removal of Equipement
(1)
Remove the container, the safety barriers and the warning notice.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
1EFF : ALL 1 32-51-43Page 409 1 1 Aug 01/05 1 1 1CES 1 SERVO CONTROL - NOSE WHEEL STEERING (6GC) - REMOVAL/INSTALLATION
________________________________________________________________
TASK 32-51-51-000-001
Removal of the Nose Wheel Steering Servo-Control (6GC)
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Self Explanatory
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific blanking plugs
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific spatula
No specific warning notice(s)
No specific container 5 l (1.3208 USgal)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
29-00-00-864-001 Put the Related Hydraulic System in the Depressurized Configuration before Maintenance Action 29-14-00-614-001 Depressurization of the Hydraulic Reservoirs R 32-51-51-991-001-A Fig. 401
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(64)
