1EFF : ALL 1 32-51-42Page 409 1 1 Aug 01/05 1 1 1CES 1 1EFF : ALL 1 32-51-42Page 410 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
3. Job Set-up__________
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 32-51-42-860-059
A. Aircraft Maintenance Configuration
(1) In the cockpit, on the center pedestal, make sure that the free-fall control handle is in the normal position.
(2) On the nose gear leg, on the electrical box, make sure that the towing lever is in the TOWING position.
(3) Make sure that the container is in position below the cylinder.
(4) Make sure that the Green hydraulic system is depressurized (Ref. TASK 29-10-00-864-001).
R **ON A/C 401-499,
R Subtask 32-51-42-860-059-A
R A. Aircraft Maintenance Configuration
R R (1) In the cockpit, on the center pedestal, make sure that the free-fall control handle is in the normal position.
R R (2) On the nose gear leg, on the electrical box, make sure that the towing lever is in the TOWING position.
R (3) Make sure that the container is in position below the cylinder.
R R (4) Make sure that the Yellow hydraulic system is depressurized (Ref. TASK 29-10-00-864-002).
Subtask 32-51-42-941-057
B. Safety Precautions
(1)
Make sure that the warning notice(s) is (are) in position to tell persons no to operate the landing gear.
(2)
Make sure that the safety barriers are in position.
(3)
Make sure that you obeyed the applicable safety precautions (Ref. TASK 32-00-00-860-001).
Subtask 32-51-42-865-057
C. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------
49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
4. Procedure
_________
(Ref. Fig. 401/TASK 32-51-42-991-001)
Subtask 32-51-42-560-052
A. Preparation for Installation
(1) Make sure that the parts retained from the removed component are clean and in the correct condition.
NOTE : Lubricate the seals with hydraulic fluid.
____
(2)
Put a new seal (7) with its backuprings on the piston (3). The rounded edge of the backuprings must be against the sides of the seal (7).
(3)
Clean the attachment hardware with CLEANING AGENTS (Material No. 11-004A) and dry with filtered compressed air.
1EFF : ALL 1 32-51-42Page 411 1 1 Aug 01/05 1 1 1CES 1
(4) Apply a light coat of SPECIAL MATERIALS (Material No. 05-047) to the
threads of all the screws. Subtask 32-51-42-420-053
B. Installation of the Steering Cylinder
(1)
Apply hydraulic fluid the cylinder (1).
(2)
Apply SPECIAL MATERIALS (Material No. 05-047) to the outer mating diameter and to the contact faces of the cylinder (1).
(3)
Put the cylinder (1) in position. NOTE : Before the installation of the rear cylinder, fully turn the
____ wheels of the NLG manually to the right.
(4)
Install the split washer (4).
(5)
Install the nine screws (6) and the nine lockwashers (5).
(6)
TORQUE the screws (6) to between 3 and 3.4 m.daN (22.12 and 25.07 lbf.ft) and safety them with corrosion resistant steel lockwire 0.8 mm (0.03 in.) dia..
(7)
Remove the blanking plugs from the line end.
(8)
Connect the hydraulic couplings (2).
(9)
TORQUE the hydraulic couplings (2) to between 2.42 and 3.16 m.daN
(17.84 and 23.30 lbf.ft).
(10)
Apply SEALANTS (Material No. 09-002) to the mating faces and to the heads of the bolts (6).
(11)
Release the disconnected electrical bundle from the leg.
(12)
Remove the blanking caps from the electrical connectors.
(13)
Connect the electrical connector (9) to the proximity-sensor (10).
1EFF : ALL 1 32-51-42Page 412 1 1 Aug 01/05 1 1 1CES 1 Subtask 32-51-42-865-058
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------49VU L/G/LGCIU/SYS1/NORM 1GA C09 121VU HYDRAULIC/LGCIU/SYS2 2GA Q35 121VU HYDRAULIC/LGCIU/SYS1/GRND SPLY 52GA Q34
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(61)
