-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
To check the nose wheel steering (NWS) zero position , with the Nose Wheel
Alignment Tool.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
R No specific circuit breaker(s) safety clip(s) No specific warning placard No specific 1.2m(4ft.)square steel plates JT2000AIRBUS 1 NOSE WHEEL ALIGNMENT TOOL
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
1EFF : ALL 1 32-51-00Page 601 1 1 Aug 01/04 1 1 1CES 1 C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-12-00-582-001 08-22-00-200-001 09-10-00-584-002 24-41-00-861-002
24-41-00-862-002
29-10-00-863-001
R 29-10-00-863-002 29-10-00-864-001
R 29-10-00-864-002 53-15-11-010-001 53-15-11-410-001 32-51-00-991-031 32-51-00-991-033 Jacking for Nose Gear Wheel ChangePrecise LevelingTowing with the Nose Gear from the FrontEnergize the Aircraft Electrical Circuits from the External PowerDe-energize the Aircraft Electrical Circuits Supplied from the External PowerPressurize the Green Hydraulic System Pressurize the Yellow Hydraulic SystemDepressurize the Green Hydraulic System Depressurize the Yellow Hydraulic SystemOpening of the Radome 110ALClosing of the Radome 110ALFig. 601Fig. 602
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
32-51-00-991-034 Fig. 603
**ON A/C 301-399,
32-51-00-991-034-A Fig. 603A
1EFF : ALL 1 32-51-00Page 602 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________
Subtask 32-51-00-865-111
A. Make sure that this(these) circuit breaker(s) is(are) open, safetied and tagged
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
Subtask 32-51-00-865-113
B. Make sure that this(these) circuit breaker(s) is(are) closed:
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU ENGINE/ENG2/OIL/PRESS 2EN2 N42 121VU ENGINE/ENG1/OIL/PRESS 2EN1 N40
Subtask 32-51-00-941-061
C. General
(1)
Put a warning placard in the cockpit to tell persons not to operate the landing gear or the N/WS.
(2)
On the panel 400VU, make sure that the L/G normal control lever is in the DOWN position.
(3)
On the nose gear leg, on the nose wheel steering deactivation electrical box, make sure that the towing lever is in the normal position (engaged position).
(4)
Make sure that the N/WS handwheels and the rudder pedals are in the neutral position.
1EFF : ALL 1 32-51-00Page 603 1 1 Aug 01/05R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 301-399,
Subtask 32-51-00-860-081
D. Aircraft Maintenance Configuration
(Ref. Fig. 601/TASK 32-51-00-991-031)
(1) Move the aircraft and position the nosewheels on the two 1.2m(4ft.)square steel plates
(a)
Position a steel plate in front of the nosewheels
(b)
Apply a thick layer of COMMON GREASE (Material No. 04-004) or COMMON GREASE (Material No. 04-022) to the upper surface of the steel plate
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(30)
