(2)
Remove the warning notice(s).
(3)
Make sure that the work area is clean and clear of tool(s) and other items.
R 1EFF : 001-004, 051-054, 1 32-51-19Page 408 1 1 May 01/05 1 1 1CES 1 Subtask 32-51-19-410-050
B. Close Access
(1) Close the doors of the nose landing gear (Ref. TASK 32-22-00-410-001).
R 1EFF : 001-004, 051-054, 1 32-51-19Page 409 1 1 May 01/05 1 1 1CES 1R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
TASK 32-51-19-000-001-A Removal of the Nose Wheel Steering Feedback Sensor Box (3GC, 4GC) P/N E21336000 CAUTION : IF THE SENSOR BOX HAS P/N E21336000, NEVER REMOVE THE SENSOR FROM THE
_______ GEARBOX. THE SENSOR AND THE GEARBOX ARE AN ASSEMBLY THAT YOU MUST NOT DISASSEMBLE ON THE AIRCRAFT. IF YOU REMOVE THE SENSOR FROM THE GEARBOX:
-YOU WILL CAUSE DAMAGE TO THE SENSOR BOX
-THE ADJUSTMENT OF THE SENSOR BOX WILL NO LONGER BE CORRECT. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
WARNING : MAKE SURE THAT ALL THE CIRCUITS IN MAINTENANCE ARE ISOLATED BEFORE
_______
YOU SUPPLY ELECTRICAL POWER TO THE AIRCRAFT.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific blanking caps
No specific circuit breaker(s) safety clip(s)
No specific safety barriers
No specific warning notice
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
07-11-00-581-003 Lifting of the Aircraft at Forward Jacking Point, MLG Wheels on the Ground 32-51-19-991-002 Fig. 402
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-19Page 410 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
3. Job Set-up
__________ Subtask 32-51-19-941-054
A. Safety Precautions
(1)
In the cockpit, on the panel 400VU, put a warning notice in position to tell persons not to operate the landing gear control lever.
(2)
On the CAPT and F/O NWS handwheels and on the brake pedals, put warning notices in position to tell persons not to operate them.
(3) Put safety barriers in position. Subtask 32-51-19-865-059
B. Open, safety and tag this(these) circuit breaker(s):
-------------------------------------------------------------------------------PANEL DESIGNATION IDENT. LOCATION -------------------------------------------------------------------------------121VU HYDRAULIC/BRAKING AND STEERING/SYS2/SPLY 4GG M36 121VU HYDRAULIC/BRAKING AND STEERING/SYS2/CTL 3GG M35 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/CTL 1GG M34 121VU HYDRAULIC/BRAKING AND STEERING/SYS1/IND AND/SPLY 2GG M33
Subtask 32-51-19-860-055
C. Aircraft Maintenance Configuration
(1) Jack up the front of the aircraft (Ref. TASK 07-11-00-581-003). NOTE : When the shock absorber is fully extended the NLG is
____ automatically in the center position (the nose wheel steering is in the zero position).
4. Procedure
_________ (Ref. Fig. 402/TASK 32-51-19-991-002) Subtask 32-51-19-020-054
A. Removal of the Sensor Box
(1)
Disconnect the electrical connector (8) from the sensor box (7).
(2)
Put blanking caps on the disconnected electrical connectors.
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-19Page 411 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
Sensor Box P/N E21336000
Figure 402/TASK 32-51-19-991-002
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-19Page 412 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1
(3)
Remove the screws (1), the washers (2), the bushes (3) and the springs (4).
(4)
Carefully remove the sensor box (7) with the spacers (5) from the nose landing gear.
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-19Page 413 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 TASK 32-51-19-400-001-A
Installation of the Nose Wheel Steering Feedback Sensor Box (3GC, 4GC) P/N E21336000
CAUTION : IF THE SENSOR BOX HAS P/N E21336000, NEVER REMOVE THE SENSOR FROM THE
_______ GEARBOX. THE SENSOR AND THE GEARBOX ARE AN ASSEMBLY THAT YOU MUST NOT DISASSEMBLE ON THE AIRCRAFT. IF YOU REMOVE THE SENSOR FROM THE GEARBOX:
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(41)
