(h)
On panel 402VU, put the A/SKID & N/W STRG switch in ON position.
____
COMMON GREASE (Material No. 04-015).
R 1EFF : 001-004, 051-054, 1 32-51-00Page A514 1 1 Aug 01/05 1 1 1CES 1
(3)
Stage 2:
(a)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(2) set the selector switch to U1.
(b)
Record the voltage (U1*)(in AC voltage).
(c)
On the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST
(2) set the selector switch to U2.
(d)
Record the voltage (U2*)(in AC voltage).
(e)
Calculate the algebraic value U*:
(U1* - U2*) = U*
(f)
Check that the algebraic value U*:
U* = 0 +/- 20 mV
(g)
If U* is not in the tolerance do the procedure from step (2) again.
(4)
On the panel 402VU, put the A/SKID & N/W STRG switch in OFF position.
(5)
Remove the SENSOR-VOLTAGE TEST (F26792000) or SENSOR - VOLTAGE TEST (2).
(6)
Connect the electrical connector (3) to the RVDT 3GC (1).
(7)
Do the procedure again for the RVDT 4GC (monitor channel).
(8) On the panel 402VU, put the A/SKID & N/W STRG switch in ON position. Subtask 32-51-00-865-082
C. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 3GG, 4GG
5. Close-up
________ Subtask 32-51-00-581-055
A. Lower the aircraft to the ground (Ref. TASK 07-11-00-586-001).
1EFF : 001-004, 051-054, 1 32-51-00Page A515 1 1 Aug 01/05R 1 1 1CES 1
Subtask 32-51-00-740-054
B. Bite Test
(1) Do the Bite test of the BSCU (Ref. TASK 32-46-00-740-001). Subtask 32-51-00-942-061
C. Remove the Equipment
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : 001-004, 051-054, 1 32-51-00Page A516 1 1 Aug 01/05R 1 1 1CES 1
R **ON A/C 005-049, 055-099, 101-149, 151-199, 201-299, 301-399, 401-499,
TASK 32-51-00-820-002-A
Adjustment of the NWS "Zero" Position for A/C with NWS Sensor Box (3GC,4GC) P/N E21336000, NLG Centering Cams as reference
CAUTION : IF THE SENSOR BOX HAS P/N E21336000, NEVER REMOVE THE SENSOR FROM THE
_______ GEARBOX. THE SENSOR AND THE GEARBOX ARE AN ASSEMBLY THAT YOU MUST NOT DISASSEMBLE ON THE AIRCRAFT. IF YOU REMOVE THE SENSOR FROM THE GEARBOX:
-YOU WILL CAUSE DAMAGE TO THE SENSOR BOX
-THE ADJUSTMENT OF THE SENSOR BOX WILL NO LONGER BE CORRECT.
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1. Reason for the Job
__________________
Do this procedure when you have a Sensor Box P/N E2133600 installed on the NLG and when you use the NLG centering cams as reference for the adjustment. R
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific circuit breaker(s) safety clip(s)
No specific spatula
No specific warning placard
No specific AC voltmeter (minimum range: 0-20V, accuracy: 1 mV,
frequency: 50-2000 Hz)
No specific Torque Wrench : range 0.00 to 1.20 m.daN
(0.00 to 9.00 lbf.ft)
F26792000 1 SENSOR-VOLTAGE TEST
R 1EFF : 005-049, 055-099, 101-149, 151-199, 1 32-51-00Page A517 1201-299, 301-399, 401-499, 1Aug 01/05 1 1 1CES 1 -------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
F26792000-1 1 SENSOR - VOLTAGE TEST
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架9(16)
