-
the eye-end (16)
-
the washer (6)
-
the new lock washer (7)
-
the locknut (8).
(11)
Install the washer (6) and the new lock washer (7) on the eye-end (16).
(12)
Install the eye-end (16) in the strut (5).
(13)
Adjust the eye-end (16) to set the dimension 'B'. NOTE : One 1/2 turn of the eye-end (16) gives 0.6 mm (0.0236 in.) of
____ movement of the uplock hook inboard or outboard.
(14)
After the adjustment of the eye-end (16). Make sure that (Dimension 'Z') is not more than 239 mm (9.4094 in.) maximum and 222 mm (8.7401 in.) minimum.
1EFF : ALL 1 32-31-00Page A525 1 1 May 01/05 1 1 1CES 1
(15)
Tighten the locknut (8) with your hand.
(16)
Align the eye-end (16) in the attachment bracket.
(17)
Install the bolt (20), the washer (19) and the locknut (18).
(18) Tighten the locknut (18) with your hand. Subtask 32-31-00-820-066
E. MLG Clearance Check
(1) Make sure that the dimensions are correct (Ref. TASK 32-31-00-820-004) . If they are not, do the adjustment procedure again.
Subtask 32-31-00-820-067
F. Safety the Attachment Points
(1)
Torque the locknuts (1) and (8) to between 1.30 and 1.40 m.daN
(115.04 and 123.89 lbf.in).
(2)
Safety the locknuts (1) and (8) with the lock washers (2) and (7).
(3)
Torque the locknut (10) to 14.6 m.daN (107.66 lbf.ft).
(4)
Safety the locknut (10) with MISCELLANEOUS (Material No. 19-010).
(5)
Torque the attachment bolt locknuts (15) and (18) to between 6.8 and
7.8 m.daN (50.14 and 57.52 lbf.ft).
(6)
Safety the locknuts (18) with the cotter pins (17) and the locknut
(15) with the cotter pin (12).
(7)
Connect the free-fall linkage mechanism to the uplock unit (Ref. TASK 32-31-44-400-001).
(8)
Install the hinged fairing that was removed (Ref. TASK 32-12-13-400-001). Make sure that the hinged fairing clearances are correct.
(9)
Install the fixed fairing that was removed (Ref. TASK 32-12-14-400-001). Make sure that the fixed fairing clearances are correct.
(10) Remove the access platform(s).
1EFF : ALL 1 32-31-00Page A526 1 1 May 01/05 1 1 1CES 1 Subtask 32-31-00-720-067
G. Functional Test of the MLG
(1) Do a functional test of the extension and retraction of the MLG (Ref. TASK 32-31-00-720-002).
5. Close-up
________ Subtask 32-31-00-860-096
A. Aircraft Maintenance Configuration
(1)
Depressurise the Green hydraulic system (Ref. TASK 29-10-00-864-001).
(2)
De-energize the aircraft electrical circuits (Ref. TASK 24-41-00-862-002).
Subtask 32-31-00-410-070
B. Close Access
(1) Make sure that the MLG door that was open for maintenance is closed (Ref. TASK 32-12-00-410-001).
Subtask 32-31-00-942-088
C. Removal of Equipment
(1)
Remove the warning notice(s).
(2)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-31-00Page A527 1 1 May 01/05 1 1 1CES 1
TASK 32-31-00-820-004 MLG Clearance Check WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______ START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______ GEAR.
WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR.
_______
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific plastic ty-wraps No specific safety barriers 98DNSA20208060 2 RIGGING PIN 98D32104018000 2 SETTING TOOL-UPLOCK 98F32304000000 2 FALSE TARGET
1EFF : ALL 1 32-31-00Page A528 1 1 May 01/05 1 1 1CES 1 B. Referenced Information
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架4(93)
