(2)
Remove the warning notice(s).
(3)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 32-22-15Page 406 1 1 Feb 01/04R 1 1 1CES 1
R TASK 32-22-15-010-001
R Removal of the Leg Door Assy for Access
R WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING_______
R GEAR.
R WARNING : MAKE SURE THAT THE TRAVEL RANGES OF THE LANDING GEAR ARE CLEAR._______
R WARNING : MAKE SURE THAT THE CONTROLS AGREE WITH THE POSITION OF THE ITEMS THEY_______
R OPERATE BEFORE YOU PRESSURIZE A HYDRAULIC SYSTEM.
R 1. Reason for the Job__________________
R This procedure is only applicable when the leg door assy is removed for
R access. For the applicable procedure to remove the leg door assy for
R replacement, Ref. TASK 32-22-15-000-001.
R 2. Job Set-up Information______________________
R A. Fixtures, Tools, Test and Support Equipment
R -------------------------------------------------------------------------------
R REFERENCE QTY DESIGNATION
R -------------------------------------------------------------------------------
R No specific safety barriers
R No specific warning notice(s)
R B. Referenced Information
R -------------------------------------------------------------------------------
R REFERENCE DESIGNATION
R -------------------------------------------------------------------------------
R 32-22-15-991-001 Fig. 401
1EFF : ALL 1 32-22-15Page 407 1 1 Aug 01/99 1 1 1CES 1 1EFF : ALL 1 32-22-15Page 408 1 1 Aug 01/99 1 1 1CES 1 TASK 32-22-15-410-001
R 3. Job Set-up__________
R Subtask 32-22-15-941-052
R A. Safety Precautions
R (1) In the cockpit, on the panel 400VU, put warning notice(s) in position
R to tell persons not to operate the landing gear control lever.
R (2) In the cockpit, on the steering handwheels (CAPT and F/O) and on the
R brake pedals, put warning notice(s) in position to tell persons not
R to operate them.
R (3) Put the safety barriers in position.
R 4. Procedure_________
R (Ref. Fig. 401/TASK 32-22-15-991-001)
R Subtask 32-22-15-020-051
R A. Removal of the Leg Door Assy
R NOTE : Do not change the adjustment of the rod (11), the rod end of the____
R fitting (2) and the rod ends of the support (10).
R (1) Remove the nut (5) and the bolt (1) and disconnect the end fitting
R (2).
R (2) Remove the bushes (3) and (4), disconnect the rod (11).
R (3) Remove the nuts (7) and the bolts (9).
R (4) Remove the bushes (8) and disconnect the fairing (6) from the support
R (10).
R (5) Remove the fairing (6).
Installation of the Leg Door Assy after Removal for Access
1. Reason for the Job
__________________
This procedure is only applicable when the leg door assy was removed for access. For the applicable procedure to install the leg door assy after replacement, Ref. TASK 32-22-15-400-001.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice(s)
R No specific Torque Wrench : range 0.00 to 1.20 m.daN
R (0.00 to 9.00 lbf.ft)
B. Consumable Materials
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
Material No. 04-004 USA MIL-PRF-23827 TYPE I
SYNTH.ESTER BASED GREASE HIGH PRESSURE
(Ref. 20-31-00)
Material No. 04-022 USA MIL-PRF-81322 GRADE 2
SYNTHE.HYDROCARBON GREASE HIGH PRESSURE
(Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架4(20)
