B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
32-22-00-010-001 Nose Gear Doors - Ground Doors Opening 32-31-41-000-001 Removal of the NLG main door control rod 32-31-73-000-005 Removal of the NLG Proximity-Sensors 12GA, 13GA,
18GA, 19GA, 24GA, 25GA, 30GA, 31GA, 37GA (36GA), 39GA (38GA)
R **ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,
32-22-11-991-001 Fig. 401
1EFF : ALL 1 32-22-11Page 401 1 1 May 01/05 1 1 1CES 1 -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R **ON A/C 106-149, 213-299, 301-399, 401-499,
32-22-11-991-001-A Fig. 401A
**ON A/C ALL
3. Job Set-up
__________
Subtask 32-22-11-941-050
A. Safety Precautions
(1) In the cockpit, on the panel 400VU put warning notice(s) in position to tell persons not to operate the landing gear control lever.
(2) Put the safety barriers in position.
Subtask 32-22-11-010-050
B. Get Access
(1)
Open the doors of the nose landing gear (Ref. TASK 32-22-00-010-001).
(2)
Put the access platform in position below the applicable NLG door.
4. Procedure
_________
**ON A/C 001-049, 051-099, 101-105, 151-199, 201-212,
(Ref. Fig. 401/TASK 32-22-11-991-001) R **ON A/C 106-149, 213-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 32-22-11-991-001-A)
1EFF : ALL 1 32-22-11Page 402 1 1 Aug 01/05 1 1 1CES 1
NLG Main Doors
Figure 401/TASK 32-22-11-991-001
R 1EFF : 001-049, 051-099, 101-105, 151-199, 1 32-22-11Page 403 1201-212, 1May 01/05 1 1 1CES 1
NLG Doors Figure 401A/TASK 32-22-11-991-001-A
R 1EFF : 106-149, 213-299, 301-399, 401-499, 1 32-22-11Page 404 1 1 Aug 01/05 1 1 1CES 1R **ON A/C ALL
Subtask 32-22-11-020-050
A. Removal of the Main Door
(1)
Removal of the applicable NLG main door control rod (Ref. TASK 32-31-41-000-001).
(2)
Remove the nuts (2) and the bolts (8).
(3)
Disconnect the bonding braids (7).
(4)
Remove the proximity sensors from the NLG doors (Ref. TASK 32-31-73-000-005)
(5)
Cut and remove the cotter pins (3) and (13), remove the nuts (4) and (14).
(6)
Remove the washers (5) and (12) and the bolts (6) and (10).
(7)
Remove the door (1).
1EFF : ALL 1 32-22-11Page 405 1 1 May 01/03 1 1 1CES 1 TASK 32-22-11-400-001
Installation of the Main Door Assy
1. Reason for the Job
__________________
This procedure is only applicable when the main door assy is installed after replacement. For the applicable procedure to install the main door assy after removal for access only, Ref. TASK 32-22-11-410-001.
2. Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific warning notice(s)
No specific access platform 1.7 m (5 ft. 7 in.)
B. Consumable Materials
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
R Material No. 04-022 USA MIL-PRF-81322 GRADE 2 R SYNTHE.HYDROCARBON GREASE HIGH PRESSURE R (Ref. 20-31-00)
C. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM LANDING GEAR 起落架4(3)
