1EFF : ALL 1 28-12-41Page 602 1 1 Aug 01/04 1 1 1CES 1
4. Procedure
_________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
(Ref. Fig. 601/TASK 28-12-41-991-001)
**ON A/C 301-399,
(Ref. Fig. 601A/TASK 28-12-41-991-001-A)
**ON A/C ALL
Subtask 28-12-41-210-052
A. Inspection of the Overpressure Protector 46QM(47QM) CAUTION : DO NOT APPLY PRESSURE TO THE SAFETY DISC BECAUSE IT WILL EASILY
_______
BREAK.
(1) Examine the overpressure protector (1) to make sure that:
-
there is no damage to the wire mesh (2)
-
there is no damage to the safety disc (3)
-the sealant on the nuts and the ends of the bolts (4) is in the correct condition
-it is correctly installed on the access panel (5)
-there is no corrosion.
5. Close-up
________
Subtask 28-12-41-410-053
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Install the access panel 550CB(650CB) (Ref. TASK 28-12-45-400-002).
1EFF : ALL 1 28-12-41Page 603 1 1 Aug 01/05 1 1 1CES 1
Overpressure Protectors - Wing and Vent Surge Tanks
Figure 601/TASK 28-12-41-991-001
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-12-41Page 604 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1R Overpressure Protectors - Wing and Vent Surge Tanks R Figure 601A/TASK 28-12-41-991-001-A
R 1EFF : 301-399, 1 28-12-41Page 605 1 1 May 01/04 1 1 1CES 1 Subtask 28-12-41-942-052
B. Removal of Equipment
(1)
Remove the safety barriers.
(2)
Remove the warning notice(s).
(3)
Remove the access platform(s).
(4)
Remove the ground support and maintenance equipment, the special and standard tools and all other items.
1EFF : ALL 1 28-12-41Page 606 1 1 May 01/04R 1 1 1CES 1
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
TASK 28-12-41-200-001 Inspection of the Overpressure Protector 102QM (103QM) WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE. WARNING : MAKE SURE THAT THE GROUND SAFETY-LOCKS ARE IN POSITION ON THE LANDING
_______
GEAR.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific safety barriers
No specific access platform 3.5 m (11 ft. 6 in.)
R 1EFF : 001-049, 051-099, 101-149, 151-199, 1 28-12-41Page 607 1201-299, 401-499, 1Aug 01/05 1 1 1CES 1 B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
12-11-28-650-003 Pressure Refuel with Automatic Control
28-10-00-910-001 Safety Procedures When You Do Work in a Fuel Tank
28-10-00-910-002 Access to the Fuel Tanks and the Work Areas
28-25-00-650-001 Pressure Defuel
28-25-00-650-003 To Drain Remaining Fuel from the Wing Tanks and the
Center Tank
28-25-00-869-001 Fuel Transfer
57-27-11-000-002 Removal of the Access Panel (540HB, 540JB, 540KB,
540LB, 540MB, 540NB, 540PB, 540QB, 540RB, 550AB,
550BB, 550CB, 550DB, 560AB, 640HB, 640JB, 640KB,
....)
57-27-11-400-002 Installation of the Access Panel (540HB, 540JB,
540KB, 540LB, 540MB, 540NB, 540PB, 540QB, 540RB,
550AB, 550BB, 550CB, 550DB, 560AB, 640HB, 640JB,
....)
28-12-41-991-001 Fig. 601
3. Job Set-up__________
Subtask 28-12-41-941-050
A. Safety Precautions
WARNING : OBEY THE SAFETY PROCEDURES WHEN YOU DO WORK IN A FUEL TANK.
_______
(1) You must obey the fuel safety procedures (Ref. TASK 28-10-00-910-001) when you do work in a fuel tank.
(2) Put the safety barriers in position. Subtask 28-12-41-860-054
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUEL 燃油2(5)
