曝光台 注意防骗
网曝天猫店富美金盛家居专营店坑蒙拐骗欺诈消费者
and periodically thereafter.
The “Debug” icon is useful when you run into a repeatable problem. JDTLLC tech support
will request that you run with Debug highlighted and send them the file for analysis. You do
not want to run in Debug mode unless instructed to as the file sizes can get quite large.
Finally, the “About” icon displays details about your version of Radar Contact, and optionally
about your computer.
We can now close Radar Contact and launch Flight Simulator for the last bit of configuration.
FSUIPC Setup
In FS9, click on the FS9 modules menu item, then click FSUIPC. In FSX, click on the FSX
add-ons menu item, and then click FSUIPC. You will see something like this
Radar Contact Quick Start Guide
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 34
Make sure the “FSUIPC multiline display window” checkbox is checked, and the “Hide all
single line messages” checkbox is checked.
Click OK
Step 5 - Radar Contact and Other Add-On Software Incompatibilities
Radar Contact will not function properly if either FSHotSeat or FSHotSFX is installed. When
either FSHotSeat or FSHotSFX is loaded for the first time, it permanently changes the
FSUIPC TCASid parameter (in the FSUIPC.INI file) from Flight to Type+. This means that
AI aircraft are now always identified by type and model rather than by airline and flight
number, regardless of the application currently using FSUIPC. This adversely affects RC AI
chatter.
Users of Active Sky V need to go into the Startup and General group box of the Options
Form and disable the item titled “Voice ATIS/Flightwatch” as well as check the box “Disable
Text Messages”. Otherwise, you will receive ASV ATIS reports on 122.0 over the top of
RC‟s instructions.
Step 6 - Fly the Flight Plan in FS X, FS2004
When you are ready to start your flight, click on Start RCv4. Radar Contact will minimize to
the task bar (this may take 30-60 seconds). Maximize Flight Simulator.
NOTE: Do not change time parameters in FS after RC launch, especially if you intend on
saving an rcd file for later use. Risks include unrealistic AI sequence and out-of-place
clearances, the rcd file itself will fail to be produced and other unrealistic events.
RC will display a screen similar to this:
Radar Contact Quick Start Guide
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 35
CID is your first checkpoint
86m is the distance to that point
70 is the no-wind heading to that point
114.10 is the frequency you should be tuned to.
Are you ready to start your flight?
1. Press 2 to get a weather briefing. Set the altimeter after listening to the briefing.
2. Next, get your clearance from Clearance Delivery by pressing 1. Set your altitude and
squawk code!
3. The screen will change to something like this:
4. If you need to Push and Start, Press 2.
5. When ready to taxi, Press 1 to contact Ground Control.
6. Taxi to the runway 13, or request a different runway by Pressing 2.
7. Then runway 13 threshold is 3095 ft on a heading of 300 from your current position.
8. As you approach the end of runway 13, Ground will tell you to contact Tower. The
display will change to something like this:
9. Press 1 to contact Tower or 2 to request a different runway.
10. Follow Tower‟s directions either hold short or taxi into position and hold.
11. Taxi on to the runway and takeoff when told to do so.
12. Shortly after leaving the ground, Tower will tell you to contact Departure. The screen
will be similar to this:
Radar Contact Quick Start Guide
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 36
13. Press 1 to contact Departure.
14. The controller will give you heading and altitude settings. Make the changes.
15. At this time, you can give the plane and comms to the co-pilot if you want. Ctrl-Shift-
K gives the comms to co-pilot Ctrl-Shift-M gives the plane to co-pilot.
16. The screen will change to something like this:
Options 2 and 5 are optional depending on what you want to do.
Notice “Main -0 Next-9?
If you press 9 you will get to what we call Page 2.
Page 2 shows more options if you need them:
Go back to the main page by pressing 0 or 8. For this flight, do not select these menu
selections.
At this point, give the plane (assuming the plane has a standard MS autopilot capability) and
comms to your co-pilot and watch what he does in relation to what is showing on the RC
screen.
Congratulations. Enjoy your flight!
Radar Contact ATC Basics
Version 4 December 2, 2007
Copyright JDT LLC 2005 Page 37
ATC Basics
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：
航空资料15(77)
