-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
53-35-13-000-002 Removal of the Quick-Release Access Panels from the Belly Fairing Structure 53-35-13-400-002 Installation of the Quick-Release Access Panels on the Belly Fairing Structure 53-31-00-991-026 Fig. 701
3. Job Set-up
__________
Subtask 53-31-00-010-077
A. Get Access
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION
_______
BEFORE YOU START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
(1)
Install the LOCKING TOOL - FLAP/SLAT CONTROL LEVER (98D27803000000) on the slat/flap control lever when working near the flaps/slats.
(2)
Put the warning notice on the slat/flap control lever to tell persons not to operate the slats.
(3)
Put the adjustable access platform in position.
(4)
Remove the quick-release panels (Ref. TASK 53-35-13-000-002):
-191BB and 191EB from the left side,
-192EB and 192FB from the right side.
Subtask 53-31-00-110-070
B. Cleaning Procedure
R WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE THIS/THESE
_______ R MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
EFF : ALL
53-31-00Page 702
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(1) Remove the old temporary protection compound from the area to be treated with a non metallic scraper, and clean with CLEANING AGENTS (Material No. 11-004) and a lint free cloth. Make sure that the area is dry before you continue.
4. Procedure
_________
CAUTION : DO NOT APPLY TEMPORARY PROTECTION ON THE OXYGEN SYSTEMS.
_______ MAKE SURE THAT THE TEMPORARY PROTECTION DOES NOT GET: -ON COMPOSITE PARTS, CONTROL CABLES, PULLEYS,TEFLON BEARINGS. -ON LUBRICATED SURFACES. -IN DRAIN VALVES OR OTHER ORIFICES. TEMPORARY PROTECTION ON OR IN THESE PARTS CAN CAUSE DAMAGE.
R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 53-31-00-916-064
A. Temporary Protection Procedure
(Ref. Fig. 701/TASK 53-31-00-991-026)
(1) Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-005A) or STORAGE PRESERVATION (Material No. 15-006) or equivalent to the pressure bulkhead AFT face at FR35 and the bottom surface of the pressure deck between FR35 and FR36.
EFF : ALL
53-31-00Page 703
Pressure Bulkhead AFT Face at FR35 and Bottom Surface of Pressure Deck between
FR35 and FR36
Figure 701/TASK 53-31-00-991-026
EFF : ALL 53-31-00 Page 704
Feb 01/98
CES
R **ON A/C 301-399,
R Subtask 53-31-00-916-064-A
R R A. Temporary Protection Procedure (Ref. Fig. 701/TASK 53-31-00-991-026)
R R R R (1) Apply STORAGE PRESERVATION (Material No. 15-005) or STORAGE PRESERVATION (Material No. 15-005A) or STORAGE PRESERVATION (Material No. 15-006) or equivalent to the pressure bulkhead AFT face at FR35 and the bottom surface of the pressure deck between FR35.8 and FR36.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身2(98)
