Wing to Fuselage Fairings - 191BT/192BT and 191CT/192CT Figure 603/TASK 53-35-00-991-006
R EFF : CES ALL 53-35-00 Page 609 May 01/04
|-------------|----------------------------------|----------------------------| | Panel FIN | Belly Fairing Missing Fasteners | | | | Description | | |-------------|----------------------------------|----------------------------| | | with the subsequent condition: | | | | - that a minimum of four | | | | fasteners of the first fastener| | | | positions are installed on all | | | | corners of each panel (count | | | | from the corner). | | |-------------|----------------------------------|----------------------------| | 191DT/192DT | Missing fasteners are not | Replace the missing | | | permitted on the FWD edge of each| fasteners before 10 flight | | | panel. | cycles | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of four | | | | fasteners of the first fastener| | | | positions are installed on all | | | | corners of each panel (count | | | | from the corner). | | |-------------|----------------------------------|----------------------------| | 191EB/192EB | Missing fasteners are not | Replace the missing | | | permitted on the FWD edge of each| fasteners before 10 flight | | | panel. | cycles | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of two fasteners| | | | of the first fastener positions| | | | are installed on all corners | | | | of each panel (count from the | | | | corner). | | |-------------|----------------------------------|----------------------------| | 191ET/192ET | Missing fasteners are not | Replace the missing | | 191KB/192KB | permitted when they are located | fasteners before 10 flight | | 197BB/198BB | directly in the area of service | cycles | | 147CB/147BB | panels. | | | 148FB/148DB | Missing fasteners are only | | | 197GB/198GB | permitted on a maximum of two | | | 196AB/197AB | sides on each panel. | | | 191GB/191HB | | | | 191JB/195AB | At panels without sealing | | | 147AB/195CB | profiles: | | |-------------|----------------------------------|----------------------------| | Panel FIN | Belly Fairing Missing Fasteners | | | | Description | | |-------------|----------------------------------|----------------------------| | 147EB/147FB | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of two fasteners| | | | of the first fastener positions| | | | are installed on all corner | | | | areas of each panel (count from| | | | the corner). | | | | | | | | At panels with sealing profiles: | | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of four | | | | fasteners of the first fastener| | | | positions are installed on all | | | | corner areas of each panel | | | | (count from the corner). | | |-------------|----------------------------------|----------------------------| | 191BT/192BT | (Ref. Fig. 603/TASK 53-35-00-991-| Replace the missing | | 191CT/192CT | 006-001) | fasteners before 10 flight | | | 1 - Missing fasteners are not | cycles | | | permitted in the corner areas| | | | 2 - Three missing fasteners are | | | | permitted when two fasteners | | | | are installed at each side of| | | | an empty hole. | | | | 3 - One missing fastener is | | | | permitted. | | | | 4 - Two missing fasteners are | | | | permitted when they are not | | | | adjacent to each other. | | |-------------|----------------------------------|----------------------------|
R **ON A/C 151-199, 401-499,
Subtask 53-35-00-210-051-A
A. Do an inspection of the wing to fuselage fairings and the belly fairing access panels for missing fasteners. (Ref. Fig. 601A/TASK 53-35-00-991-004-A, 602/TASK 53-35-00-991-005, 603/TASK 53-35-00-991-006)
NOTE : You can temporarily replace a missing fastener by a fastener from
____ another panel. Make sure that the replacement fastener has the same thread size and the same length as the missing one. Obey the criterias in the subsequent table when you remove a fastener from any other panel.
|-------------|----------------------------------|----------------------------| | Panel FIN | Belly Fairing Missing Fasteners | | | | Description | | |-------------|----------------------------------|----------------------------| | 7504MM | No missing fastener permitted. | | | 7505MM | | | | | | | |-------------|----------------------------------|----------------------------| | 193AB/194AB | No missing fastener permitted. | | | 193BB/194BB | | | | | | | |-------------|----------------------------------|----------------------------| | 191BB/192FB | Missing fasteners are not | Replace the missing | | | permitted on the FWD edge of each| fasteners before 10 flight | | | panel. | cycles | | | Missing fasteners are permitted, | | | | only if in accordance with the | | | | subsequent condition: | | | | - that a minimum of two fasteners| | | | in the first fastener positions| | | | are installed on all corners of| | | | each panel (count from the | | | | corner). | | |-------------|----------------------------------|----------------------------| | 191AB/191AT | Missing fasteners are not | Replace the missing | | 191LB/192AB | permitted on the FWD edge of each| fasteners before 10 flight | | 192AT/192LB | panel. | cycles | | | Two missing fasteners are | | | | permitted, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of four | | |-------------|----------------------------------|----------------------------| | Panel FIN | Belly Fairing Missing Fasteners | | | | Description | | |-------------|----------------------------------|----------------------------| | | fasteners of the first fastener| | | | positions are installed on all | | | | corners of each panel (count | | | | from the corner). | | |-------------|----------------------------------|----------------------------| | 191DT/192DT | Missing fasteners are not | Replace the missing | | | permitted on the FWD edge of each| fasteners before 10 flight | | | panel. | cycles | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of four | | | | fasteners of the first fastener| | | | positions are installed on all | | | | corners of each panel (count | | | | from the corner). | | |-------------|----------------------------------|----------------------------| | 191EB/192EB | Missing fasteners are not | Replace the missing | | | permitted on the FWD edge of each| fasteners before 10 flight | | | panel. | cycles | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of two fasteners| | | | of the first fastener positions| | | | are installed on all corners | | | | of each panel (count from the | | | | corner). | | |-------------|----------------------------------|----------------------------| | 191ET/192ET | Missing fasteners are not | Replace the missing | | 191KB/192KB | permitted when they are located | fasteners before 10 flight | | 197BB/198BB | directly in the area of service | cycles | | 147CB/147BB | panels. | | | 148FB/148DB | Missing fasteners are only | | | 197GB/826DR | permitted on a maximum of two | | | 196AB/198MB | sides on each panel. | | | 191GB/191HB | | | | 191JB/195AB | At panels without sealing | | | 147AB/195CB | profiles: | | | 147EB/147FB | One fastener at every fourth | | | 197AB | fastener position is permitted | | |-------------|----------------------------------|----------------------------| | Panel FIN | Belly Fairing Missing Fasteners | | | | Description | | |-------------|----------------------------------|----------------------------| | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of two fasteners| | | | of the first fastener positions| | | | are installed on all corner | | | | areas of each panel (count from| | | | the corner). | | | | | | | | At panels with sealing profiles: | | | | One fastener at every fourth | | | | fastener position is permitted | | | | missing, only if in accordance | | | | with the subsequent condition: | | | | - that a minimum of four | | | | fasteners of the first fastener| | | | positions are installed on all | | | | corner areas of each panel | | | | (count from the corner). | | |-------------|----------------------------------|----------------------------| | 191BT/192BT | (Ref. Fig. 603/TASK 53-35-00-991-| Replace the missing | | 191CT/192CT | 006-001) | fasteners before 10 flight | | | 1 - Missing fasteners are not | cycles | | | permitted in the corner areas| | | | 2 - Three missing fasteners are | | | | permitted when two fasteners | | | | are installed at each side of| | | | an empty hole. | | | | 3 - One missing fastener is | | | | permitted. | | | | 4 - Two missing fasteners are | | | | permitted when they are not | | | | adjacent to each other. | | |-------------|----------------------------------|----------------------------| CES
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身2(105)
