May 01/04
R
CES -------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
ASRM 53-31-11-201 (for corrective action) 53-31-00-991-016 Fig. 614
3. Job Set-up
__________
Subtask 53-31-00-010-075
A. Get Access
(1) Put the adjustable platform in position below the inspection area.
Subtask 53-31-00-860-053
B. Preparation of the Inspection Areas
(Ref. Fig. 614/TASK 53-31-00-991-016)
(1) Make sure that the surfaces of the inspection areas are clean and smooth.
WARNING : OBEY THE MANUFACTURER'S INSTRUCTIONS WHEN YOU USE
_______ THIS/THESE MATERIAL/S. USE PROTECTIVE CLOTHING, RUBBER GLOVES, GOGGLES AND A MASK.
WARNING : MAKE SURE THAT THERE IS A GOOD FLOW OF AIR THROUGH THE WORK
_______ AREA WHEN YOU USE SPECIAL MATERIALS. IF YOU GET ONE OF THESE MATERIALS ON YOUR SKIN, IN YOUR MOUTH OR IN YOUR EYES : -FLUSH IT AWAY WITH A FLOW OF CLEAN WATER FOR BETWEEN 10 AND 15 MINUTES. -GET IMMEDIATE MEDICAL AID IF IRRITATION OCCURS. DO NOT BREATHE THE FUMES FROM THE MATERIAL. DO NOT SMOKE WHEN YOU USE THE MATERIAL. DO NOT USE THE MATERIAL NEAR A FLAME, SPARKS OR SOURCES OF HEAT. THESE MATERIALS ARE DANGEROUS : THEY ARE POISONOUS, FLAMMABLE AND SKIN IRRITANTS.
(2)
If necessary, clean the inspection areas with the CLEANING AGENTS (Material No. 11-004) and a MISCELLANEOUS (Material No. 19-003). Make sure the inspection areas are dry before you continue.
(3)
If necessary, make the surface of the inspection areas smooth with the abrasive cloth, grade 280.
EFF : ALL 53-31-00Page A632
May 01/04
R
CES
(4)
Do a visual inspection of the inspection areas. Look for damage and defects in the shape of the external surface.
(5)
If you find damage :
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-Refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage.
4. Procedure
_________
(Ref. Fig. 614/TASK 53-31-00-991-016)
R **ON A/C 001-049, 051-099, 101-149, 201-299,
Subtask 53-31-00-220-053
A. Special Detailed Inspection Procedure
(1)
Do the special detailed inspection of the lower skin of the longitudinal lap joints in the crack stopper areas. Do this at STGR6 LH/RH, between FR35 and FR47, on the external surface (Ref. NTM 533126-Part.6).
(2)
Write a report if you find damage during the inspection procedure.
(3)
If you find damage:
(a)
Refer to the ASRM (Ref. ASRM 51-11-00-001) for the classification of the damage.
(b)
If you find corrosion damage:
-
refer to the ASRM (Ref. ASRM 51-22-00-001) for the general corrosion data
-
refer to the ASRM (Ref. ASRM 51-74-00-001) for the repair of the corroded areas.
(c)
If you find other types of damage:
-
refer to the ASRM (Ref. ASRM 51-73-00-001) for the repair of the minor damage
-
refer to the ASRM (Ref. ASRM 53-31-11-101) for the allowable damage limits for this structure
-
refer to the ASRM (Ref. ASRM 53-31-11-201) for the repair data for this structure.
R **ON A/C 151-199, 401-499,
Subtask 53-31-00-220-053-A
A. Special Detailed Inspection Procedure
(1)
Do the special detailed inspection of the lower skin of the longitudinal lap joints in the crack stopper areas. Do this at STGR6 LH/RH, between FR35 and FR47/51, on the external surface (Ref. NTM 533126-Part.6).
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM FUSELAGE 机身2(75)
