(b)
Safety the bolt (7) with the retaining ring (8).
4. Procedure
_________ Subtask 52-42-15-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Close the access panel 134AR and/or 154AR.
1EFF : ALL 1 52-42-15Page 405 1 1 Feb 01/98 1 1 1CES 1
DOOR - HP AIR GROUND CONNECTOR - REMOVAL/INSTALLATION
_____________________________________________________ TASK 52-42-16-000-001 Removal of the HP Air-Ground Connector Door (191DB)
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------REFERENCE QTY DESIGNATION -------------------------------------------------------------------------------
No specific access platform 1.50 m (4 ft. 11 in.)
B. Referenced Information
-------------------------------------------------------------------------------REFERENCE DESIGNATION -------------------------------------------------------------------------------
52-42-16-991-001 Fig. 401
3. Job Set-up
__________ Subtask 52-42-16-010-050
A. Get Access
(1)
Put an access platform in position in zone 191.
(2)
Open the access door 191DB.
1EFF : ALL 1 52-42-16Page 401 1 1 Feb 01/98 1 1 1CES 1
4. Procedure
_________ Subtask 52-42-16-020-050
A. Removal of the HP Air Ground Connector Door
(Ref. Fig. 401/TASK 52-42-16-991-001)
(1)
Release the spring (3) from the frame fitting.
(2)
Hold the door (2).
(3)
Remove the nuts (6) and the bolts (1) from the hinges (4).
(4)
Retain the spring fitting (5).
(5)
Remove the door (2).
1EFF : ALL 1 52-42-16Page 402 1 1 Feb 01/98 1 1 1CES 1
HP Air Ground Connector Door 191DB
Figure 401/TASK 52-42-16-991-001
1EFF : ALL 1 52-42-16 Page 403
1 1 Feb 01/98
1 1
1CES 1
TASK 52-42-16-400-001
1. Reason for the Job
Installation of the HP Air-Ground Connector Door (191DB) __________________ Self Explanatory
2. Job Set-up Information______________________
A. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
20-28-00-912-004 Bonding with Conductive Bolts and Screws and Bonding Straps in the Fuselage and in the Wings (this does not include the tanks)
52-42-16-991-001 Fig. 401
3. Job Set-up
__________ Subtask 52-42-16-860-050
A. Aircraft Maintenance Configuration
(1)
Make sure that the access platform is in position.
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
4. Procedure
_________ Subtask 52-42-16-420-050
A. Installation of the HP Air Ground Connector
(Ref. Fig. 401/TASK 52-42-16-991-001)
(1)
Put the door (2) and the hinge (4) in position on the door frame.
(2)
Install the spring fitting (5) on the hinge (4).
1EFF : ALL 1 52-42-16Page 404 1 1 Feb 01/98 1 1 1CES 1
(3) Install the bolts (1) and the nuts (6) and tighten them. NOTE : Do an electrical bonding when you install the bolts (1) and
____ (6) on each side of the hinge (4) (Ref. TASK 20-28-00-912-004).
(4) Attach the spring (3) on the fitting (5). Subtask 52-42-16-210-051
B. Check of the Door Opening/Closing
(1)
Open and close the door.
(2)
Make sure that the door operate correctly.
5. Close-up
________ Subtask 52-42-16-410-050
A. Close Access
(1)
Close the door 191DB.
(2)
Make sure that the work area is clean and clear of tool(s) and other items.
(3)
Remove the access platform(s).
1EFF : ALL 1 52-42-16Page 405 1 1 Feb 01/98 1 1 1CES 1
DOOR - GROUND SERVICE CONDITIONED AIR CONNECTION - REMOVAL/INSTALLATION
_______________________________________________________________________ TASK 52-42-17-000-001 Removal of the Ground Service Conditioned-Air Connection-Door (191CB)
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门7(7)
