1EFF : 301-399, 1 52-42-22Page 414 1 1 May 01/04 1 1 1CES 1
(3)
If necessary, adjust contour offset as follows:
(a)
Remove the access panel 197KB as necessary (Ref. TASK 53-35-13-000-002).
(b)
Loosen the screws (31).
(c)
Adjust the latch hook (30) until you get the correct values.
(d)
Tighten the screws (31).
(e)
Install the access panel 197KB as necessary (Ref. TASK 53-35-13-400-002).
(4)
Make sure that the gap between access door (2) and the panel 197KB is correct.
NOTE : The gap on the hinge side can be between 2.0 mm (0.0787 in.)
____ and 4.0 mm (0.1574 in.). The gap on the other sides can be between 1.0 mm (0.0393 in.) and 5.0 mm (0.1968 in.).
(5) Make sure that the access door (2) correctly closed and locked.
**ON A/C ALL
5. Close-up
________ R **ON A/C 001-049, 051-099, 101-149, 151-199, 201-299, 401-499,
Subtask 52-42-22-410-050
A. Close Access
(1)
Make sure that the work area is clean and clear of tool(s) and other items.
(2)
Remove the access platform(s).
1EFF : ALL 1 52-42-22Page 415 1 1 Aug 01/05 1 1 1CES 1 1EFF : 301-399, 1 52-42-22Page 416 1 1 May 01/04 1 1 1CES 1 DOOR - YELLOW HYDRAULIC SYSTEM GROUND SERVICE PANEL - REMOVAL/INSTALLATION
R **ON A/C 301-399,
R Subtask 52-42-22-410-050-A
R A. Close Access
R (1) Make sure that the work area is clean and clear of tool(s) and other
R items.
R (2) Remove the access platform(s).
__________________________________________________________________________
TASK 52-42-23-000-001
Removal of the Ground Service Panel Door of the Yellow Hydraulic System (198CB)
WARNING : PUT THE SAFETY DEVICES AND THE WARNING NOTICES IN POSITION BEFORE YOU
_______
START A TASK ON OR NEAR:
-
THE FLIGHT CONTROLS
-
THE FLIGHT CONTROL SURFACES
-
THE LANDING GEAR AND THE RELATED DOORS
-COMPONENTS THAT MOVE.
1.
Reason for the Job
__________________
Self Explanatory
2.
Job Set-up Information
______________________
A. Fixtures, Tools, Test and Support Equipment
-------------------------------------------------------------------------------
REFERENCE QTY DESIGNATION
-------------------------------------------------------------------------------
No specific access platform 2.0 m (6 ft. 7 in.)
B. Referenced Information
-------------------------------------------------------------------------------
REFERENCE DESIGNATION
-------------------------------------------------------------------------------
53-35-13-000-002 Removal of the Quick-Release Access Panels from the Belly Fairing Structure
**ON A/C 001-049, 051-061, 101-103, 201-203,
52-42-23-991-001 Fig. 401 R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
52-42-23-991-001-A Fig. 401A
1EFF : ALL 1 52-42-23Page 401 1 1 Aug 01/05 1 1 1CES 1 **ON A/C ALL
3. Job Set-up
__________
**ON A/C 001-049, 051-061, 101-103, 201-203,
(Ref. Fig. 401/TASK 52-42-23-991-001) R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
(Ref. Fig. 401A/TASK 52-42-23-991-001-A)
**ON A/C 001-049, 051-061, 101-103, 201-203,
Subtask 52-42-23-010-050
A. Get Access
(1)
Put the access platform in position below the ground service panel door of the Yellow hydraulic system 198CB.
(2)
Open the access door 198CB.
(3)
If it is necessary to remove the hinges (3) and (4), or the spring bolt assembly of the access door (1):
-remove the access panel 198BB (Ref. TASK 53-35-13-000-002). R **ON A/C 062-099, 104-149, 151-199, 204-299, 301-399, 401-499,
Subtask 52-42-23-010-050-A
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM DOORS 舱门7(15)
