(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Apply a small quantity of COMMON GREASE (Material No. 04-032) to the flange of the auto motor/s.
(4)
Apply a small quantity of COMMON GREASE (Material No. 04-033) to the teeth of the shaft of the auto motor/s and to the threads of the screws (42).
(5)
Put the auto motor(s) (43) 10HL-3 and/or (44) 10HL-4 in position on the outflow valve (5) and install the screws (42).
(6)
Make sure that the metal plug of the auto motor 10HL-4 (43) points away from the gear-box mechanism linkage to the Electronics Module 10HL-1.
(7)
Make sure that the metal plug of the auto motor 10HL-3 (44) points down from the automotor 10HL-4 (43).
(8)
TORQUE the screws (42) to between 0.05 and 0.06 m.daN (4.42 and 5.30 lbf.in).
(9)
Remove the blanking caps from the disconnected electrical connectors.
(10)
Make sure that the electrical connectors are clean and in the correct condition.
(11)
Connect the electrical connectors:
-
for the auto motor (43) 10HL-3 the electrical connector (32),
-
for the auto motor (44) 10HL-4 the electrical connector (35).
(12)
Put the electrical cable(s) (40) and/or (45) in position and install the new cable ties (41) where necessary.
NOTE : When the gear-box mechanism linkage moves, it must not touch
____ the cable(s) (40) (45) or the metal plugs of the auto motors.
R 1EFF : 001-049, 051-099, 101-105, 1 21-31-51Page 484 1 1 Aug 01/05 1 1 1CES 1
(13) Make sure that the work area is clean and clear of tool(s) and other
items. R **ON A/C 106-149, 151-199, 201-299, 301-399, 401-499,
Subtask 21-31-51-420-052-A
A. Installation of the Auto Motor
(1)
Clean the component interface and/or the adjacent area.
(2)
Make sure that the parts retained from the removed component are clean and in the correct condition.
(3)
Apply a small quantity of COMMON GREASE (Material No. 04-032) to the flange of the auto motor/s.
(4)
Apply a small quantity of COMMON GREASE (Material No. 04-033) to the teeth of the shaft of the auto motor/s and to the threads of the screws (42).
(5)
Put the auto motor(s) (43) 10HL-3 and/or (44) 10HL-4 in position on the outflow valve (5) and install the screws (42).
(6)
Make sure that the metal plug of the auto motor 10HL-4 (43) points away from the gear-box mechanism linkage to the Electronics Module 10HL-1.
(7)
Make sure that the metal plug of the auto motor 10HL-3 (44) points down from the auto motor 10HL-4 (43).
(8)
TORQUE the screws (42) to between 0.05 and 0.06 m.daN (4.42 and 5.30 lbf.in).
(9)
Remove the blanking caps from the disconnected electrical connectors.
(10)
Make sure that the electrical connectors are clean and in the correct condition.
(11)
Connect the electrical connectors:
-
for the auto motor (43) 10HL-3 the electrical connector (32),
-
for the auto motor (44) 10HL-4 the electrical connector (35).
(12)
Put the electrical cable(s) (40) and/or (45) in position and install the new cable ties (41) where necessary.
NOTE : When the gear-box mechanism linkage moves, it must not touch
____ the cable(s) (40) (45) or the metal plugs of the auto motors.
(13)
Put the bonding strap (4) in position and temporarily install the washer (28) and the bolt (27).
(14)
Put the grill (9) in position in the retaining clips (10) and install the quick-release fasteners (12).
(15)
Remove the bolt (27) and the washer (28).
(16)
Put the bonding straps (4) and (11) in position and install the washer (28) and the bolt (27) (Ref. TASK 20-28-00-912-004).
(17)
Make sure that the work area is clean and clear of tool(s) and other items.
**ON A/C ALL
Subtask 21-31-51-865-057
B. Remove the safety clip(s) and the tag(s) and close this(these) circuit breaker(s): 1HL, 2HL, 3HL, 6HU, 30HN
Subtask 21-31-51-710-052
C. Pressure Control and Monitoring System Tests NOTE : The Operational Test of the Pressure Control and Monitoring System
____ must be performed on both system channels. Ensure that TEST OK or a failure message is displayed. If the test is interrupted it must be restarted until TEST OK or a failure message is displayed.
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR CONDITIONING 空调 3(46)
