R 1EFF : 062-099, 1 21-31-51Page 425 1 1 May 01/05 1 1 1CES 1
R (17) Make sure that the work area is clean and clear of tool(s) and other
R items.
R Subtask 21-31-51-420-064-D
R B. Installation of the Outflow Valve
R WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR_______
R INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
R NOTE : This paragraph is only applicable for outflow valve P/N 20790-01AA____
R and subsequent.
R Make sure that there is no blanking plug installed in the static
R port of the outflow valve electronic boxes.
R (1) Make sure that the parts retained from the removed component are
R clean and in the correct condition.
R (2) Clean the component interface and/or the adjacent area.
R (3) Make sure that the gasket (6) is in a good condition. If necessary
R replace the gasket (6).
R (4) Make sure that the joining faces of the outflow valve (5) and the
R aircraft structure are free from grease and sealants.
R (5) Loosen the nuts (32).
R NOTE : Only loosen the nuts sufficiently to allow the support____
R brackets (25) to move up or down.
R (6) Put the gasket (6) in position on the outflow valve (5).
R (7) Carefully put the outflow valve (5) and the gasket (6) in position.
R NOTE : The outflow valve weighs approx. 12.5 kg (27.5577 lb).____
R NOTE : Make sure that the location pins (8) are in the correct____
R position in the outflow valve support-structure.
R (8) From the outside of the aircraft install the outflow valve
R attach-screws (7).
R NOTE : Install the screws (7) as identified in the removal procedure.____
R (9) TORQUE in sequence (refer to sequence chart) the screws (7) to
R between 0.46 and 0.54 m.daN (40.70 and 47.78 lbf.in).
R 1EFF : 062-099, 1 21-31-51Page 426 1 1 May 01/05 1 1 1CES 1
(10)
Install the bolts (22) and the washers (21) in the support brackets (25).
(11)
Tighten the bolts (22).
(12)
Tighten the nuts (32).
(13)
Put the bonding strap (4) in position on the outflow valve (5) and install the washer (28) and the bolt (27) (Ref. TASK 20-28-00-912-004).
(14)
Remove the blanking caps from the disconnected electrical connectors.
(15)
Make sure that the electrical connectors are clean and in the correct condition.
(16)
Connect the electrical connectors (1) 10HL-B, (3) 10HL-A, (23) 10HL-E, (26) 10HL-D and (2) 10HL-C in that order.
(17)
Make sure that the work area is clean and clear of tool(s) and other items.
R **ON A/C 106-149, 151-199, 204-299, 301-399, 401-499,
Subtask 21-31-51-420-050-B
A. Installation of the Outflow Valve WARNING : SUPPORT THE UNIT/ASSEMBLY OR IT WILL FALL AND BECOME DAMAGED OR
_______ INJURE PERSONNEL. THE UNIT/ASSEMBLY IS HEAVY.
NOTE : This paragraph is only applicable for outflow valves P/N
中国航空网 www.aero.cn
航空翻译 www.aviation.cn
本文链接地址：A320飞机维护手册 AMM AIR CONDITIONING 空调 3(30)
